Differences

This shows you the differences between two versions of the page.

--- public:radio:gm4slv_allstar [24/04/23 15:50 BST] – [Hardware] john
+++ public:radio:gm4slv_allstar [26/04/23 14:39 BST] (current) – removed john
@@ Line 1: / Line 1: @@
-<-[[.:start]]
-====== GM4SLV Allstar ======
-** UHF Allstar Gateway **
-===== Hardware =====
-|Platform|Rapsberry Pi|
-|Connectivity|[[Allstar|All Star Node 48148]]|
-|Interface|CM108 Soundcard|
-|Radio|FT-8900|
-|Frequency|430.050MHz|
-|Monitor|[[http://gm4slv.plus.com:42111/allmon2/link.php?nodes=48148|Allmon2]]|
-===== Config =====
-echolink.conf
-[el0]
-call = GM4SLV-L                          ; Change this!
-pwd = oldtrout                           ; Change this!
-name = John                        ; Change this!
-qth = allstar 48148                           ; Change this!
-email = gm4slv@gm4slv.plus.com                         ; Change this!
-node = 886089                           ; Change this!
-; Data for EchoLink Status Page
-lat = 60.2883                               ; Latitude in decimal degrees
-lon = -001.42533                               ; Longitude in decimal degrees
-freq = 430.050                              ; not mandatory Frequency in MHz
-tone = 0.0                              ; not mandatory CTCSS Tone (0 for none)
-power = 1                               ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts)
-height = 0                              ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet)
-gain = 0                                ; Gain in db (0-9)
-dir = 0                                 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction)
-maxstns = 5                            ; Max Stations
-rtcptimeout = 10
-recfile = /tmp/echolink_recorded.gsm    ;
-astnode = 48148             ; Change this!
-context = radio-secure                  ; Default in code is echolink-in
-; Max 3 servers
-server1 = server1.echolink.org
-server2 = server2.echolink.org
-server3 = server3.echolink.org
-; To deny w6xxx you would add the statement: deny = w6xxx
-; To prohibit computer-based connections you would write: permit = *-*
-; To allow access to only a select group of callsigns: permit = w6abc,w6def,...
-; permit                                ; comma delimited list of callsign, type (-r)
-; deny
-; Remote text commands thru netcat:
-; o.conip <IPaddress>    (request a connect)
-; o.dconip <IPaddress>   (request a disconnect)
-; o.rec                  (turn on/off recording)
-; ipaddr
-; port
-#includeifexists custom/echolink.conf
-===== Commands =====
- * DTMF Commands
-  * Please send * 7 3 to ensure all links are disconnected before making any new links
-^Command	^DTMF Sequence^
-|Disconect from Node xxxx	|  * 1 xxxx  |
-|Connect RX Only to xxxx	|  * 2 xxxx  |
-|Connect Transceive to xxxx	|  * 3 xxxx  |
-|Speak the Node Status	|  * 7 0  |
-|Disconnect ALL nodes	|  * 7 3  |
-|Reconnect ALL nodes	|  * 7 4  |
-|Send Node ID	|  * 8 0  |
-|Speak the Local Time	|  * 8 1  |
-|Parrot ON	|  * 9 1  |
-|Parrot OFF	|  * 9 2  |
-|Parrot ONCE	|  * 9 3  |
-^  Number  ^  Name  ^* 5 Macro shortcut to...	^  DTMF Sequence  ^  Node No.  ^
-|  1  |  Fedihams | Connect RX Only to Fedihams |  * 5 2 1  |  57881 |
-|  1  |  Fedihams | Connect Transceive to Fedihams |  * 5 3 1  |  57881 |
-|  1  |  Fedihams | Disconnect from Fedihams |  * 5 1 1  |  57881 |
-|  2  |  Hubnet  |Connect RX Only to Hubnet	|  * 5 2 2  |  41223  |
-|  2  |  Hubnet  |Connect Transceive to Hubnet	|  * 5 3 2  |  41223  |
-|  2  |  Hubnet  |Disconnect from Hubnet	|  * 5 1 2  |  41223  |
-===== Courtesy Tones =====
-Can give information about the node status.
-After a local Transmission on the "input" frequency the reponse will be one of:
-  * Morse Letter **I** (di-dit) = node is not connected to any other nodes
-  * Morse Letter **R** (di-dah-dit) = node is connected in "Monitor/RX only" mode to one or more nodes
-  * Morse Letter **K** (dah-di-dah) = node is connected in "Transceive" mode to one or more nodes
-There are other tones, e.g. when a station on a linked node unkeys there's a low-pitched "bloop"
-When a local RF station sends a command there's a "bip bip" (not to be confused with the Morse letter I)
-===== Echolink =====
-AllStar nodes can also connect to [[https://www.echolink.org/logins.jsp|Echolink]]
-The node can connected to Echolink as ''GM4SLV-L ''
-(**UPDATE** --- //John Pumford-Green 24/04/23 14:47// )
-I have disabled the Echolink connection by editing ''/etc/asterisk/modules.conf'' to change the channel driver for Echolink to ''noload'' ->
-<code conf>
-noload => chan_echolink.so ;
-</code>
-an Asterisk reload is necessary:
-<code bash>
-gm4slv@mb7aze:/etc/asterisk$ sudo astres.sh
-Restarting Asterisk
-systemctl restart asterisk.service
-</code>
---- //John Pumford-Green 24/04/23 14:44//
-===== Further Information =====
-{{tag>}}