John's Vademecum

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
<-[[.:start]]


====== Netradio Control ======

** Python code for TCP/IP control of multiple radios **

===== Server =====

This provides TCP/IP access to one or more radios, allowing control of Frequency, Mode, Pre-amp and Attenuator. It also gives remote access to S-meter readings.

There are separate rig-dependant command modules that then provide a standard interface for commands sent by a client, regardless of the particular radio connected.

There are modules for

  * Icom C-IV radios such as IC-R75, IC-718, IC-7200 etc.
  * AOR AR7030
  * Icom IC-M710 marine 

==== Server ====

++++ server.py |

<file python server.py>
from aor import *
from icom import *
from conf import *
from m710 import *
import SocketServer
import time

try:
    import readline
except:
    pass

lock = threading.Lock()

radios = []



r1 = Icom(n1, a1, cal1)
radios.append(n1)

r2 = m710(n4)
radios.append(n4)

#r2 = Icom(n2, a2, cal2)
#radios.append(n2)

r3 = Ar7030(n3)
radios.append(n3)

print radios
#print r1.digi_off()

#print r2.remote_on()

def count_radios():
    count = len(radios)
    return count


def list_radios():
    radiolist = ""
    for n in range(0, len(radios)):
        r = radios[n]
        radiolist += (r + " ")
    return radiolist


def write_file(text):
    filename = 'commandlog.txt'
    f = open(filename, 'a+')  # a+ is "append to file, create it if it doesn't exist"
    timenow = time.strftime("%d/%m/%Y %H:%M:%S", time.gmtime(time.time()))
    log = " ".join((timenow, text))  # make an entry for the log by joining the timestamp with the text passed in
    f.write(log)
    f.close()


def write_con(text):
    filename = 'conlog.txt'
    f = open(filename, 'a+')  # a+ is "append to file, create it if it doesn't exist"
    timenow = time.strftime("%d/%m/%Y %H:%M:%S", time.gmtime(time.time()))
    log = " ".join((timenow, text))  # make an entry for the log by joining the timestamp with the text passed in
    f.write(log)
    f.close()


# The Server
class ThreadedRequestHandler(SocketServer.StreamRequestHandler):
    def handle(self):
        # we find the current thread for the client connection just set up, to
        # use in the log file
        cur_thread = threading.currentThread()
        # log the new connection details
        write_con("Connect from %s using %s \n" % ((self.client_address[0]), cur_thread.getName()))
        # print to the server's console the new connection IP address/port
        print self.client_address
        # loop to handle client requests....
        while True:
            # using StreamRequestHandler means our input from the client
            # is  "file-like" and can be read with "file-like" commands
            # we read a line at a time, using readline()
            cmd = self.rfile.readline().lower()
            # to keep things clean, we remove any characters that aren't
            # "printable" simple ASCII
            # these are between 32 and 127 in the ASCII table
            # we look at each character, and then make a new word by
            # .join()ing each accepted character with no space in between
            asccmd = "".join(x for x in cmd if ord(x) < 128 and ord(x) > 31)
            # we make a list called "words" holding the received words which
            # will be inspected by various functions
            words = asccmd.split()
            # If a client uses sock.close() itself, to disconnect, it appears that
            # we read a continuous stream of "" on the dead
            # socket, which puts CPU to 100%.
            #
            # The "While" loop is probably responsible, but I can't see another
            # way to keep the connection up for multiple commands.
            #
            # Further connection are accepted due to the Threaded nature of the server.
            # The CPU load is unacceptable though
            # HACK ?>>>>>
            # Looking for "" and then breaking
            # the connection from the server end (even though the client has
            # gone) cures this.
            if cmd == "":
                break
            else:
                pass
            # if the words list is empty, go back and get more input
            if not words:
                continue
            # we have input....
            # filter based on the first word - these are the
            # pre-set commands the server will accept
            # the client wants to know the currently available
            # radio names - held in the variable "rnames"
            elif words[0] == "getnames":
                self.wfile.write(rnames)
            # words[-1] (the last word in the list) will always be the
            # radio name. We give the variable "my_radio" this value, for
            # identifying which radio object to apply the method to
            elif words[0] == "count":
                count = count_radios()
                self.wfile.write(count)
            elif words[0] == "ident":
                ident_text = "GM4SLV Radio Server"
                radio_list = list_radios()
                self.wfile.write(ident_text + "\rAvailable : \n" + radio_list + "\r\n")

            elif words[0] == "getmode":
                my_radio = eval(words[-1])
                mode = my_radio.get_mode()
                self.wfile.write(mode)
            elif words[0] == "getfreq":
                my_radio = eval(words[-1])
                freq = words[1]
                freq = my_radio.get_freq()
                self.wfile.write(freq)
            elif words[0] == "setmode":
                my_radio = eval(words[-1])
                mode = words[1]
                newmode = my_radio.set_mode(mode)
                self.wfile.write(newmode)
            elif words[0] == "setfreq":
                my_radio = eval(words[-1])
                try:
                    freq = float(words[1])
                    newfreq = my_radio.set_freq(freq)
                    self.wfile.write(newfreq)
                except ValueError:
                    #freq = float(my_radio.get_freq())
                    self.wfile.write("Error in freq. %s No change\r\n" % words[1])
                    
            elif words[0] == "getsmeter":
                my_radio = eval(words[-1])
                smeter = round(float(my_radio.get_smeter()), 1)
                self.wfile.write(smeter)
            elif words[0] == "gets":
                my_radio = eval(words[-1])
                s = my_radio.get_s()
                self.wfile.write(s)
            elif words[0] == "listradios":
                radios = list_radios()
                self.wfile.write(radios)
            elif words[0] == "getpreamp":
                my_radio = eval(words[-1])
                preamp = my_radio.get_pre()
                self.wfile.write(preamp)
            elif words[0] == "preampon":
                my_radio = eval(words[-1])
                preamp = my_radio.pre_on()
                self.wfile.write(preamp)
            elif words[0] == "preamp2on":
                my_radio = eval(words[-1])
                preamp = my_radio.pre_2_on()
                self.wfile.write(preamp)
            elif words[0] == "preampoff":
                my_radio = eval(words[-1])
                preamp = my_radio.pre_off()
                self.wfile.write(preamp)
            elif words[0] == "getatt":
                my_radio = eval(words[-1])
                att = my_radio.get_att()
                self.wfile.write(att)
            elif words[0] == "atton":
                my_radio = eval(words[-1])
                att = my_radio.att_on()
                self.wfile.write(att)
            elif words[0] == "attoff":
                my_radio = eval(words[-1])
                att = my_radio.att_off()
                self.wfile.write(att)
            elif words[0] == "tune":
                my_radio = eval(words[-1])
                tune = my_radio.tune()
                self.wfile.write(tune)
            elif words[0] == "getpwr":
                my_radio = eval(words[-1])
                pwr = my_radio.get_pwr()
                self.wfile.write(pwr)
            elif words[0] == "setpwr":
                my_radio = eval(words[-1])
                spwr = words[1]
                pwr = my_radio.set_pwr(spwr)
                self.wfile.write(pwr)
            elif words[0] == "quit":
                write_con("Got quit from {}\n".format(self.client_address[0]))  # log it
                self.wfile.write("Goodbye! \r\n")  # say Goodbye
                break
            else:  # nothing in words[0] matches a pre-set command....
                write_file("Received %s\n" % words)  # log it, it's unusual
                self.wfile.write("Command not recognized\r\n")  # inform the client


class ThreadedIcomServer(SocketServer.ThreadingMixIn, SocketServer.TCPServer):
    pass


if __name__ == '__main__':
    # define the lock to be used on the serial port access
    lock = threading.Lock()

    # address ('' = all available interfaces) to listen on, and port number
    address = ('', 9999)
    server = ThreadedIcomServer(address, ThreadedRequestHandler)
    server.allow_reuse_address = True

    # define that the server will be threaded, and will serve "forever" ie. not quit after the client disconnects
    t = threading.Thread(target=server.serve_forever)
    # start the server thread
    t.start()

    write_con(
        "Server loop running in thread: %s\n" % "".join(t.getName())) 


</file>

++++

==== Configurtion Module ====

++++ conf.py |

<file python cpnf.py>
# header
preamble = "\xfe"
controller = "\xe0"

# commands/requests
set_freq_cmd = "\x05"
set_mode_cmd = "\x06"
get_freq_cmd = "\x03"
get_mode_cmd = "\x04"
get_smeter_cmd = "\x15" + "\x02"
get_swr_cmd = "\x15" + "\x12"
digi_off_cmd = "\x1a" + "\x04" + "\x00" + "\x00"

set_pre_cmd = "\x16" + "\x02"

set_pre_off = "\x00"
set_pre_on = "\x01"
set_pre_2_on = "\x02"

set_att_cmd = "\x11"
set_att_on = "\x20"
set_att_off = "\x00"

ptt_on_cmd = "\x1c" + "\x00" + "\x01"
ptt_off_cmd = "\x1c" + "\x00" + "\x00"

pwr_cmd = "\x14" + "\x0a"

# end of message
eom = "\xfd"

# controller responses
ack = "\xfb"
nak = "\xfa"

a1 = "\x5A"
n1 = "IC-R75"
cal1 = ( 25, 1, 36, 47, 31, 18, 34, 35 )

a2 = "\x5e"
# a2 = "\x01"
n2 = "IC-718"
cal2 = ( 27, 28, 58, 10, 14, 14, 35, 42 )

n3 = "AR7030"

n4 = "IC-M710"

</file>

++++


==== Icom C-IV module ====

++++ icom.py |

<file python icom.py>
import serial
import threading
from conf import *
import time
#sport = "COM1"
sport = "/dev/ttyS0"
sbaud = 9600

lock = threading.Lock()


class Icom(object):
    def __init__(self, model, radio_address, cal):
        self.ser = serial.Serial(sport, sbaud, timeout=0.1)
        self.model = model
        self.radio_address = radio_address
        self.cal = cal
    
    def digi_off(self):
        sendStr = preamble + preamble + self.radio_address + controller + digi_off_cmd + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"

    def get_pre(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_pre_cmd + eom

        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        if result[6] == "\x00":
            return 0
        elif result[6] == "\x01":
            return 1
        elif result[6] == "\x02":
            return 2

    def get_pwr(self):
        sendStr = preamble + preamble + self.radio_address + controller + pwr_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        p1 = ord(result[7]) / 16
        p2 = ord(result[7]) % 16
        p3 = ord(result[6]) / 16
        p4 = ord(result[6]) % 16
        pwr = float(100 * (10 * p3 + p4) + (10 * p1 + p2))
        return int(pwr*100/255)

    def set_pwr(self, pwr):
        #if pwr == "25":
        #    spwr = "\x00" + "\x63"
        #elif pwr == "50":
        #    spwr = "\x01" + "\x27"
        #elif pwr == "75":
        #    spwr = "\x01" + "\x91"
        #elif pwr == "100":
        #    spwr = "\x02" + "\x55"
        rigpwr = int(pwr) * 255 / 100
        print "rigpwr ", rigpwr
        pwr1 = rigpwr / 100
        pwr2 = rigpwr % 100
        spwr1 = (pwr1 / 10 * 16)
        spwr2 = (pwr1 % 10)
        spwr3 =  (pwr2 / 10 * 16)
        spwr4 =  (pwr2 % 10)
        spwr = chr(spwr1+spwr2) + chr(spwr3+spwr4)
        #print "spwr ", spwr
        sendStr = preamble + preamble + self.radio_address + controller + pwr_cmd + spwr + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return self.get_pwr()
        elif result[4] == nak:
            return "NAK received"

    def pre_on(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_pre_cmd + set_pre_on + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"
    
    def pre_2_on(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_pre_cmd + set_pre_2_on + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"


    def pre_off(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_pre_cmd + set_pre_off + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"

    def ptt_on(self):
        sendStr = preamble + preamble + self.radio_address + controller + ptt_on_cmd + eom
        result = self.tx_rx(sendStr)
        #print result[5]
        if not result[4] == ack:
            return "ptt on"
        elif result[4] == nak:
            return "Error"
    
    def ptt_off(self):
        sendStr = preamble + preamble + self.radio_address + controller + ptt_off_cmd + eom
        result = self.tx_rx(sendStr)
        #print result[5]
        if not result[4] == ack:
            return "ptt off"
        elif result[4] == nak:
            return "Error"

    def get_att(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_att_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        if result[5] == "\x00":
            return 0
        elif result[5] == "\x20":
            return 1

    def att_on(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_att_cmd + set_att_on + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"

    def att_off(self):
        sendStr = preamble + preamble + self.radio_address + controller + set_att_cmd + set_att_off + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Success"
        elif result[4] == nak:
            return "NAK received"

    def set_freq(self, freq):
        fdig = "%010d" % int(freq * 1000)
        bcd = ()
        for i in (8, 6, 4, 2, 0):
            bcd += self.freq_bcd(int(fdig[i]), int(fdig[i + 1]))
        set_freq_val = ""
        for byte in bcd:
            set_freq_val += chr(byte)
        sendStr = preamble + preamble + self.radio_address + controller + set_freq_cmd + set_freq_val + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Set Freq success"
        elif result[4] == nak:
            return "NAK received / Freq not supported"

    def get_freq(self):
        sendStr = preamble + preamble + self.radio_address + controller + get_freq_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        if len(result) > 0:
            f = 0
        for k in [18, 19, 16, 17, 14, 15, 12, 13, 10, 11]:
            f = 10 * f + self.nib(result, k)
        self.freq = (float(f) / 1000)
        return "%.3f" % self.freq

    def set_mode(self, mode):
        print "in set_mode() with ", mode
        if mode == "data":
            mode = "rtty"

        if mode == "lsb":
            set_mode_val = "\x00"
        elif mode == "usb":
            set_mode_val = "\x01"
        elif mode == "am":
            set_mode_val = "\x02"
        elif mode == "cw":
            set_mode_val = "\x03"
        elif mode == "rtty":
            set_mode_val = "\x04"
        elif mode == "fm":
            set_mode_val = "\x05"
        elif mode == "cw-r":
            set_mode_val = "\x07"
        elif mode == "rtty-r":
            set_mode_val = "\x08"
        elif mode == "s-am":
            set_mode_val = "\x11"
        else:
            return "Mode not recognized"
        sendStr = preamble + preamble + self.radio_address + controller + set_mode_cmd + set_mode_val + eom
        result = self.tx_rx(sendStr)
        if result[4] == ack:
            return "Set Mode Success"
        elif result[4] == nak:
            return "NAK received / Mode not supported"

    def get_mode(self):
        sendStr = preamble + preamble + self.radio_address + controller + get_mode_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        mode = ""
        if result[5] == "\x00":
            mode = "lsb"
        elif result[5] == "\x01":
            mode = "usb"
        elif result[5] == "\x02":
            mode = "am"
        elif result[5] == "\x03":
            mode = "cw"
        elif result[5] == "\x04":
            mode = "rtty"
        elif result[5] == "\x05":
            mode = "fm"
        elif result[5] == "\x08":
            mode = "rtty-r"
        elif result[5] == "\x07":
            mode = "cw-r"
        elif result[5] == "\x11":
            mode = "s-am"

        if mode == "rtty":
            mode = "data"

        self.mode = mode
        return self.mode.upper()

    def get_s(self):
        sendStr = preamble + preamble + self.radio_address + controller + get_smeter_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        sm1 = ord(result[7]) / 16
        sm2 = ord(result[7]) % 16
        sm3 = ord(result[6]) / 16
        sm4 = ord(result[6]) % 16
        s = float(100 * (10 * sm3 + sm4) + (10 * sm1 + sm2))
        return s
    
    def get_swr(self):
        sendStr = preamble + preamble + self.radio_address + controller + get_swr_cmd + eom
        result = self.tx_rx(sendStr)
        if not result:
            return "0"
        sm1 = ord(result[7]) / 16
        sm2 = ord(result[7]) % 16
        sm3 = ord(result[6]) / 16
        sm4 = ord(result[6]) % 16
        swr = float(100 * (10 * sm3 + sm4) + (10 * sm1 + sm2))
        return swr

    def get_smeter(self):
        s = float(self.get_s())
        cal = self.cal
        s1 = s - cal[0]
        s2 = s1 - cal[1]
        s3 = s2 - cal[2]
        s4 = s3 - cal[3]
        s5 = s4 - cal[4]
        s6 = s5 - cal[5]
        s7 = s6 - cal[6]
        if s1 <= 0:
            dbm = -123
            adj = s / cal[0] * 10
            return str(dbm + adj)
        elif s2 <= 0:
            dbm = -113
            adj = s1 / cal[1] * 10
            return str(dbm + adj)
        elif s3 <= 0:
            dbm = -103
            adj = s2 / cal[2] * 10
            return str(dbm + adj)
        elif s4 <= 0:
            dbm = -93
            adj = s3 / cal[3] * 10
            return str(dbm + adj)
        elif s5 <= 0:
            dbm = -83
            adj = s4 / cal[4] * 10
            return str(dbm + adj)
        elif s6 <= 0:
            dbm = -73
            adj = s5 / cal[5] * 10
            return str(dbm + adj)
        elif s7 <= 0:
            dbm = -63
            adj = s6 / cal[6] * 20
            return str(dbm + adj)
        else:
            dbm = -43
            adj = s7 / cal[7] * 20
            return str(dbm + adj)

    def get_name(self):
        return self.model

    def tune(self):
        print "tuning"
        curmode = self.get_mode().lower()
        #print "Current Mode ",curmode

        curpwr = self.get_pwr()
        if curpwr < 98:
            curpwr = curpwr + 1

        #print "Current Power ", curpwr
        
        #print "Current percent power ", curpwr
        self.set_mode("rtty")
        self.set_pwr(25)
        #print "Tuning power ", self.get_pwr()
        #print "PTT On"
        self.ptt_on()
        time.sleep(2)
        swr =  self.get_swr()
        #print "SWR :", swr
        time.sleep(1)
        self.ptt_off()
        #print "PTT Off"
        self.set_mode(curmode)
        #print "Mode reset ",self.get_mode()
        self.set_pwr(curpwr)
        print "Tuned : (ref pwr : %s)" % swr
        return "Tuned : (ref pwr : %s)" % swr
        
    def tx_rx(self, sendStr):
        lock.acquire()
        self.ser.write(sendStr)
        echo = self.ser.read(len(sendStr))
        if len(echo) != len(sendStr):
            return "0"
        byte = "0"
        result = ""
        count = 0
        while byte != eom:
            byte = self.ser.read()
            #print "%#02x" % ord(byte)
            result += byte
            count += 1
            if count > 10:
                break
        lock.release()
        #print ""
        return result


    def nib(self, s, i):
        k = ord(s[i / 2])
        if i % 2 == 0:
            k = k >> 4
        return k & 0xf


    def freq_bcd(self, d1, d2):
        return (16 * d1 + d2),

 

</file>

++++

==== AOR AR7030 module ====

++++ aor.py |

<file  python aor.py>
import serial
import threading


#sport = "/dev/ttyS0"
sport = "/dev/ttyUSB1"
sbaud = 1200

lock = threading.Lock()
fract = float(2 ** 24) / 44545


class Ar7030(object):
    def __init__(self, model):
        self.ser = serial.Serial(sport, sbaud, timeout=10)
        self.model = model


    def check_bit(self, byte, bit):
        mask = 1 << bit
        result = (ord(byte) & mask)
        if result:
            return 1
        else:
            return 0

    def set_bit(self, byte, bit):
        mask = 1 << bit
        result = ord(byte) | mask
        return result

    def clear_bit(self, byte, bit):
        mask = ~(1 << bit)
        result = (ord(byte) & mask)
        return result

    def get_ident(self):
        sendStr = '\x5f' + '\x40'
        ident = self.tx_rx(sendStr, False, 8)
        return ident

    def get_pre(self):
        sendStr = '\x50' + '\x32' + '\x48'
        byte = self.tx_rx(sendStr, False, 1)
        p = self.check_bit(byte, 4)
        if p:
            return 1
        else:
            return 0
        return


    def pre_on(self):
        #get current 8-bit rxcon byte :
        # bit0 = filter FS3
        # bit1 = filter FS2
        # bit2 = filter FS1
        # bit3 = filter FS4
        # bit4 = preamp enabled
        # bit5 = atten 0 = 20dB / 1 = 40dB
        # bit6 = input filter 0 = HF / 1 = LF
        # bit7 = attenuator enabled

        sendStr = '\x50' + '\x32' + '\x48'

        byte = self.tx_rx(sendStr, False, 1)

        # set bit 4 ON = preamp ON and get the new 8-bit rxcon byte
        pon = self.set_bit(byte, 4)

        # split new rxcon byte into two 4-bit nibbles, add 48/96 (\x30 and \x60)
        high = 48 + (pon >> 4)
        low = 96 + (pon & 15)

        sendStr = '\x81' + '\x50' + '\x32' + '\x48' + chr(high) + chr(low) + '\x29' + '\x80'

        self.tx_rx(sendStr, False, 0)

        return "Command sent"


    def pre_off(self):
        #get current 8-bit rxcon byte
        sendStr = '\x50' + '\x32' + '\x48'
        byte = self.tx_rx(sendStr, False, 1)

        # set bit 4 OFF = preamp OFF and get the new 8-bit rxcon byte
        pon = self.clear_bit(byte, 4)


        # split new rxcon byte into two 4-bit nibbles, add 48/96 (\x30 and \x60)
        high = 48 + (pon >> 4)
        low = 96 + (pon & 15)

        sendStr = '\x81' + '\x50' + '\x32' + '\x48' + chr(high) + chr(low) + '\x29' + '\x80'

        self.tx_rx(sendStr, False, 0)
        return "Command sent"


    def get_att(self):
        sendStr = '\x50' + '\x32' + '\x48'

        byte = self.tx_rx(sendStr, False, 1)

        a = self.check_bit(byte, 7)

        if a:
            return 1
        else:
            return 0


    def att_on(self):
        #get current 8-bit rxcon byte
        sendStr = '\x50' + '\x32' + '\x48'
        byte = self.tx_rx(sendStr, False, 1)

        # set bit 7 ON = ATT ON and get the new 8-bit rxcon byte
        pon = self.set_bit(byte, 7)


        # split new rxcon byte into two 4-bit nibbles, add 48/96 (\x30 and \x60)
        high = 48 + (pon >> 4)
        low = 96 + (pon & 15)

        sendStr = '\x81' + '\x50' + '\x32' + '\x48' + chr(high) + chr(low) + '\x29' + '\x80'

        self.tx_rx(sendStr, False, 0)
        return "Command sent"


    def att_off(self):
        #get current 8-bit rxcon byte
        sendStr = '\x50' + '\x32' + '\x48'
        byte = self.tx_rx(sendStr, False, 1)

        # set bit 7 OFF = att OFF and get the new 8-bit rxcon byte
        pon = self.clear_bit(byte, 7)


        # split new rxcon byte into two 4-bit nibbles, add 48/96 (\x30 and \x60)
        high = 48 + (pon >> 4)
        low = 96 + (pon & 15)

        sendStr = '\x81' + '\x50' + '\x32' + '\x48' + chr(high) + chr(low) + '\x29' + '\x80'

        self.tx_rx(sendStr, False, 0)
        return "Command sent"


    def set_freq(self, freq):
        fval = freq * fract
        #print fval
        b1 = 48 + int(fval / 1048576)
        fval = fval % 1048576
        b2 = 96 + int(fval / 65536)
        fval = fval % 65536
        b3 = 48 + int(fval / 4096)
        fval = fval % 4096
        b4 = 96 + int(fval / 256)
        fval = fval % 256
        b5 = 48 + int(fval / 16)
        b6 = 96 + int(fval % 16)

        f_tuple = ( b1, b2, b3, b4, b5, b6 )

        freqStr = ""
        for byte in f_tuple:
            freqStr += chr(byte)

        sendStr = '\x81' + '\x50' + '\x31' + '\x4a' + freqStr + '\x24' + '\x80'

        self.tx_rx(sendStr, False, 0)
        return "Freq Set"

    def get_freq(self):

        sendStr = '\x50' + '\x31' + '\x4a'

        freqStr = self.tx_rx(sendStr, False, 3)

        f_val = 0
        for k in freqStr:
            f_val = f_val * 256 + ord(k)

        return "%.3f" % round(float(f_val / fract),2 )
        


    def set_mode(self, mode):

        if mode == "lsb":
            set_mode_val = "\x66"
        elif mode == "usb":
            set_mode_val = "\x67"
        elif mode == "am":
            set_mode_val = "\x61"
        elif mode == "cw":
            set_mode_val = "\x65"
        elif mode == "data":
            set_mode_val = "\x64"
        elif mode == "fm":
            set_mode_val = "\x63"
        elif mode == "s-am":
            set_mode_val = "\x62"
        else:
            return "Mode not recognized"

        sendStr = '\x81' + '\x50' + '\x31' + '\x4d' + set_mode_val + '\x22' + '\x80'

        self.tx_rx(sendStr, False, 0)

        return "Mode sent"

    def get_mode(self):

        sendStr = "\x50" + "\x31" + "\x4d"
        m = self.tx_rx(sendStr, False, 1)

        mode = ""
        if m == "\x01":
            mode = "am"
        elif m == "\x02":
            mode = "s-am"
        elif m == "\x03":
            mode = "fm"
        elif m == "\x04":
            mode = "data"
        elif m == "\x05":
            mode = "cw"
        elif m == "\x06":
            mode = "lsb"
        elif m == "\x07":
            mode = "usb"

        return mode.upper()


    def get_s(self):
        sendStr = '\x2e'
        sraw = self.tx_rx(sendStr, True, 0)

        return ord(sraw)

    def get_cal(self):

        sendStr = '\x52' + '\x3f' + '\x44' + '\x11'
        #print "sending getcal"
        cbytes = self.tx_rx(sendStr, False, 8)

        cal = []

        for c in cbytes:
            cal.append(ord(c))

        return cal

    def get_smeter(self):
        s = float(self.get_s())
        cal = self.get_cal()

        s1 = s - cal[0]
        s2 = s1 - cal[1]
        s3 = s2 - cal[2]
        s4 = s3 - cal[3]
        s5 = s4 - cal[4]
        s6 = s5 - cal[5]
        s7 = s6 - cal[6]

        if s1 <= 0:
            dbm = -123
            adj = s / cal[0] * 10
            return str(dbm + adj)

        elif s2 <= 0:
            dbm = -113
            adj = s1 / cal[1] * 10
            return str(dbm + adj)

        elif s3 <= 0:
            dbm = -103
            adj = s2 / cal[2] * 10
            return str(dbm + adj)

        elif s4 <= 0:
            dbm = -93
            adj = s3 / cal[3] * 10
            return str(dbm + adj)

        elif s5 <= 0:
            dbm = -83
            adj = s4 / cal[4] * 10
            return str(dbm + adj)

        elif s6 <= 0:
            dbm = -73
            adj = s5 / cal[5] * 10
            return str(dbm + adj)

        elif s7 <= 0:
            dbm = -63
            adj = s6 / cal[6] * 20
            return str(dbm + adj)

        else:
            dbm = -43
            adj = s7 / cal[7] * 20
            return str(dbm + adj)


    def tx_rx(self, sendStr, reply, n):
        # apply thread lock
        lock.acquire()
        self.ser.write(sendStr)

        if reply:  # for reading S-meter
            result = ""
            while not result:
                result = self.ser.read(1)
            lock.release()
            return result
        else:

            result = ""
            byte = ""
            while n != 0:
                self.ser.write('\x71')
                #byte = ""

                while not byte:
                    byte = self.ser.read(1)

                result += byte

                byte = ""
                n -= 1
            lock.release()
            return result





</file>


++++

==== Icom IC-M710 module ====

++++ m710.py |

<file  python m710.0y>
'''
Python NMEA Radio Functions module for Icom IC-M710 Marine HF SSB Transceiver

    Copyright (C) 2015  John Pumford-Green

    This program is free software: you can redistribute it and/or modify
    it under the terms of the GNU General Public License as published by
    the Free Software Foundation, either version 3 of the License, or
    (at your option) any later version.

    This program is distributed in the hope that it will be useful,
    but WITHOUT ANY WARRANTY; without even the implied warranty of
    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
    GNU General Public License for more details.

    You should have received a copy of the GNU General Public License
    along with this program.  If not, see <http://www.gnu.org/licenses/>.
'''

# serial port for Icom IC-M710 Rig Control

import serial
import threading
import time
version = "v0.1"

sport = '/dev/ttyUSB0'
sbaud = 4800

#ser = serial.Serial(sport, 4800, timeout=1)
lock = threading.Lock()

# NMEA Codes
preamble = "$PICOA,"
controller = "90"
radio = "01" 
cr = "\x0d"
lf = "\x0a"


# Commands are sent as NMEA private sentences:
#
# $PICOA,controller_id,radio_id,command,<parameter>,*HH<CR><LF>
#
# where HH is the 2 digit ECC value below:
#
# The protocol document states that for messages FROM the controller TO the radio
# the ECC bytes are optional, and may be omitted. This appears to be false information, and
# the ECC bytes seem to be necessary.
#
# The ECC checksum, is a two-digit hex value found by XORing the hex values of the characters 
# between "$" and "*" (but not including the $ or *)
#
# The first part of the message is always:
# "PICOA,90,01," and this has an XOR value of (decimal) 112
# we then XOR this with each character's decimal ASCII value, in the required command
# and convert the result to a 2-digit hex value
#

class m710(object):
    def __init__(self, model):
        self.ser = serial.Serial(sport, sbaud, timeout=0.1)
        self.model = model


    def get_ecc(self,command):
        ecc = 112
        for c in command:
            ecc = ord(c) ^ ecc
        hecc = '{0:02x}'.format(int(ecc))
        
        return hecc

# we must force the radio into "Remote" mode before sending any other commands.    
    def remote_on(self):
        command = "REMOTE,ON"
        ecc = self.get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            return
        else:
            return self.remote_on()
    
        

# we can leave the radio in "Remote" mode for as long as we want to control it remotely
# but we must close the "Remote" mode when finished. The previous radio settings (channel/power etc) are
# restored after Remote mode is closed.
    def remote_off(self):
        command = "REMOTE,OFF"
        ecc = self.get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr) 
        if result:
            #ser.close()
            return
        else:
            return self.remote_off()
    

    def ptt_on():
        command = "TRX,TX"
        ecc = get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return
        else:
            return ptt_on()

    def ptt_off():
        command = "TRX,RX"
        ecc = get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return
        else:
            return ptt_off()



    def get_freq(self):
        fkhz = self.get_rxfreq()
        #fkhz = "%.3f" % (float(f) * 1000)
        return fkhz

    def set_freq(self,freq):
        
        self.set_rxfreq(freq)
        self.set_txfreq(freq)
        return "Set freq success"
            
    def get_rxfreq(self):
        command = "RXF"
        ecc = self.get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            list = result.split(",")
            f = list[4].split("*")[0]
            fkhz = "%.3f" % (float(f) * 1000)
            return fkhz
        else:
            return self.get_rxfreq()
        
        
    def get_txfreq(self):
        command = "TXF"
        ecc = get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            list = result.split(",")
            f = list[4].split("*")[0]
            fkhz = "%.3f" % (float(f) * 1000)
            return fkhz
        else:
            return self.get_txfreq()
        

    def get_mode(self):
        command = "MODE"
        ecc = self.get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            list = result.split(",")
            mode = list[4].split("*")[0]
            if mode == "J2B":
                mode = "DATA"
            return mode
        else:
            return self.get_mode()
        
       

    def set_mode(self,mode):
        mode = mode.upper()
        if mode == "DATA":
            mode = "J2B"

        command = "MODE,"+mode
        ecc = self.get_ecc(command)
        
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        #print "in set_mode with ", sendStr
        result = self.tx_rx(sendStr)
        if result:
            return result
        else:
            return self.set_mode(mode)
       
        
    def set_rxfreq(self,freq):
        
        fmhz = float(freq) / 1000
        f = str(fmhz)
        
        command = "RXF,"+f
        ecc = self.get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            return result
        else:
            return self.set_rxfreq(freq)
            
            
    def set_txfreq(self,freq):
        
        fmhz = float(freq) / 1000
        f = str(fmhz)
        
        command = "TXF,"+f
        ecc = self.get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            return result
        else:
            return self.set_txfreq(freq)

    def get_txpower():
        command = "TXP"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            list = result.split(",")
            power = list[4].split("*")[0]
            return power
        else:
            return get_txpower()

    def set_txpower(p):
        command = "TXP,"+p
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return set_txpower(p)

    def get_smeter(self):
        command = "SIGM"
        ecc = self.get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = self.tx_rx(sendStr)
        if result:
            list = result.split(",")
            smeter = (float(list[4].split("*")[0]) * 20) - 120 
            return smeter
        else:
            return self.get_smeter()

    def speaker_on():
        command = "SP,ON"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return speaker_on()
        
        
    def speaker_off():
        command = "SP,OFF"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return speaker_off()

    def sql_on():
        command = "SQLC,ON"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return sql_on()

    def sql_off():
        command = "SQLC,OFF"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return sql_off()

    def nb_on():
        command = "NB,ON"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return nb_on()

    def nb_off():
        command = "NB,OFF"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return nb_off()
            
    def dim_on():
        command = "DIM,ON"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return dim_on()

    def dim_off():
        command = "DIM,OFF"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return dim_off()
            
    def agc_on():
        command = "AGC,ON"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return agc_on()

    def agc_off():
        command = "AGC,OFF"
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return agc_off()

    def get_vol():
        command = "AFG"
        ecc = get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            list = result.split(",")
            vol = list[4].split("*")[0]
            return vol
        else:
            return get_vol()
            
            

    def set_vol(v):
        command = "AFG,"+v
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return set_vol(v)

    def get_rfg():
        command = "RFG"
        ecc = get_ecc(command)
        sendStr = preamble+controller+","+radio+","+command+"*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            list = result.split(",")
            rf = list[4].split("*")[0]
            return rf
        else:
            return get_rfg()
            
    def get_att(self):
        return
    def att_on(self):
        return
    def att_off(self):
        return
    
    def pre_on(self):
        return
    def pre_off(self):
        return

    def get_pre(self):
        return

    def set_rfg(v):
        command = "RFG,"+v
        ecc = get_ecc(command)
        sendStr = preamble +controller+","+radio+"," + command + "*"+ecc+cr+lf
        result = tx_rx(sendStr)
        if result:
            return result
        else:
            return set_rfg(v)

    # The message FROM the radio may be corrupted so we do a check on the received ECC versus our calculated cECC
    # from the received characters - which are everything AFTER the "$" and BEFORE the "*"
    #
    # starting the ECC calculation at message[1] ignores the "$" and we iterate through the message XORing each 
    # character's ASCII (decimal) value until we have the final cECC which is converted by formatting it
    # into a two-digit hex value. This is then compared to the received (rECC) value from the radio's message. 
    # If they match the message is acceptable and check_ecc() returns True to tx_rx(), 
    # otherwise check_ecc() function returns "False" to tx_rx()
    # the True/False value is tested in tx_rx(). 
    # If True then tx_rx() returns the incoming string to the calling function
    # otherwise it returns "False". 
    # The calling function then checkS the boolean state of the returned value. 
    # If True (ie it has the radio's message and the ECC was good) the message 
    # is sent back to the client. 
    # If False the function calls itself again, and attempts to get an error-free reply from the radio, via tx_rx()

    def check_ecc(self,message, recc):
        i = 1
        cecc = 0
        
        while i < len(message):
            cecc = ord(message[i]) ^ cecc
            i += 1  
            
        cecc = '{0:02x}'.format(int(cecc))  
        
        if cecc == recc:   
            return True
        else: 
            return False
            
    def tx_rx(self,sendStr):
        #print "in tx_rx, sendStr =  " , sendStr
        lock.acquire()
        
        self.ser.write(sendStr)
        time.sleep(0.1)
        result = self.ser.readline()

        #print result
        reply = result.split("*")
        ecc = reply[1][0:2].lower()
        message = reply[0]
        lock.release()
        
        if self.check_ecc(message, ecc):
            return result
        else:
            return False
        
        
           


#
    

</file>

++++


===== Text-mode client =====

++++ client.py |

<file python client.py>
__author__ = 'gm4slv'
# client to work with server_oo.py
# 

# # v0.1

import socket

try:
    import readline
except ImportError:
    pass

import threading
import time


HOST, PORT = "localhost", 9999

smlog = "pymon.txt"
log_active = []


def make_con():
    global sock
    sock = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
    sock.connect((HOST, PORT))


def get_rnum():
    global num
    global radios

    names = connect("listradios")

    radios = names.split()
    num = len(radios)
    return num


def get_rname(i):
    r = radios[i]
    return r


def list_radios():
    num = get_rnum()
    global radio
    print "\r\nThere are currently %d radios connected." % num
    for i in range(0, num):
        r = get_rname(i)
        print "Radio %d is %s" % (i + 1, r)


def get_lradio():
    num = get_rnum()

    lradio = raw_input("Select radio to log: ").strip()

    if not lradio:
        print "Please select a radio"
        return False
    elif int(lradio) > num:
        print "Selected radio not recognized"
        return False

    else:

        return lradio


def set_radio():
    num = get_rnum()
    # global radio
    global radio_num
    global rname
    print "There are currently %d radios connected." % num
    for i in range(0, num):
        r = get_rname(i)
        print "Radio %d is %s" % (i + 1, r)

    radio = raw_input("Choose a radio number from the list : ").strip()
    try:
        if not radio:
            print "Please select a radio"
            return False, False

        elif int(radio) > num:
            print "Selected radio not recognized"
            return False, False
    except ValueError:
        print "Please enter a number"
        return False, False

    else:
        radio_num = "".join(("r", radio))
        rname = get_rname(int(radio) - 1)
        return radio_num, rname


def prompt():
    print ""
    print "The available commands are:"
    print "lr   : List Radios"
    print "sr   : Select the Radio to control"
    print "gr   : Get currently selected Radio name"
    print "gm   : Get Mode"
    print "sm   : Set Mode"
    print "gf   : Get Freq"
    print "sf   : Set Freq"
    print "gs   : Get S-meter"
    print "gp   : Get Pre-amp"
    print "pon  : Set Pre-amp On"
    print "p2on : Set Pre-amp 2 On"
    print "poff : Set Pre-amp Off"
    print "gatt : Get Attn"
    print "aton : Set Attn On"
    print "atoff: Set Attn Off"
    print "ga   : Get All (status of all radios)"
    print "sync : Sync freq/mode on two radios"
    print "log  : Setup background logging to file"
    print "h    : Help (show this command list)"
    print "q    : quit"
    print ""


def start():
    global radio_num
    global rname
    global sock
    pfreq = connect("getfreq" + " " + radio_num)
    pmode = connect("getmode" + " " + radio_num)
    
    data = raw_input(rname + " (" + pfreq + " " + pmode + ") " + " > ").lower().strip()
    if len(data.split()) > 1:
        if (data.split())[0] == "sf":
            sfreq = (data.split())[1]
            freq = connect("setfreq" + " " + sfreq + " " + radio_num)
            print "%s replied: %s" % (rname, freq)
            start()
        elif (data.split())[0] == "sm":
            smode = (data.split())[1]
            mode = connect("setmode" + " " + smode + " " + radio_num)
            print "%s replied: %s" % (rname, mode)
            start()
        else:
            
            print "only one command at a time please"
            start()
    elif data == "u":
        oldf = connect("getfreq" + " " + radio_num)
        newf = str(float(oldf) + 1)
        freq = connect("setfreq" + " " + newf + " " + radio_num)
        print "%s replied: %s" % (rname, freq)
        start()
    
    elif data == "d":
        oldf = connect("getfreq" + " " + radio_num)
        newf = str(float(oldf) - 1)
        freq = connect("setfreq" + " " + newf + " " + radio_num)
        print "%s replied: %s" % (rname, freq)
        start()
        
    elif data == "lr":
        list_radios()
        start()
    elif data == "sr":

        radio_num, rname = set_radio()

        while not radio_num:
            radio_num, rname = set_radio()

        start()

    elif data == "gr":
        print "Radio selected is %s" % rname
        start()

    elif data == "gm":
        mode = connect("getmode" + " " + radio_num)
        print "%s replied: %s" % (rname, mode)
        start()

    elif data == "sm":
        smode = raw_input("Enter mode: ")
        mode = connect("setmode" + " " + smode + " " + radio_num)
        print "%s replied: %s" % (rname, mode)
        start()

    elif data == "gf":
        freq = connect("getfreq" + " " + radio_num)
        print "%s replied: %s kHz" % (rname, freq)
        start()

    elif data == "sf":
        sfreq = raw_input("Enter freq (kHz): ")
        freq = connect("setfreq" + " " + sfreq + " " + radio_num)
        print "%s replied: %s" % (rname, freq)
        start()

    elif data == "gs":
        smeter = connect("getsmeter" + " " + radio_num)
        print "%s replied: %sdBm" % (rname, smeter)
        start()

    elif data == "gp":
        preamp = connect("getpreamp" + " " + radio_num)
        print "%s replied: %s" % (rname, preamp)
        start()

    elif data == "pon":
        preamp = connect("preampon" + " " + radio_num)
        print "%s replied: %s" % (rname, preamp)
        start()
    
    elif data == "p2on":
        preamp = connect("preamp2on" + " " + radio_num)
        print "%s replied: %s" % (rname, preamp)
        start()

    elif data == "poff":
        preamp = connect("preampoff" + " " + radio_num)
        print "%s replied: %s" % (rname, preamp)
        start()

    elif data == "gatt":
        preamp = connect("getatt" + " " + radio_num)
        print "%s replied: %s" % (rname, preamp)
        start()

    elif data == "aton":
        att = connect("atton" + " " + radio_num)
        print "%s replied: %s" % (rname, att)
        start()

    elif data == "atoff":
        att = connect("attoff" + " " + radio_num)
        print "%s replied: %s" % (rname, att)
        start()

    elif data == "ga":
        get_all()
        start()


    elif data == "log":
        fname = raw_input("Enter a filename (or \"Return\" for default) :")
        if fname == "":
            fname = smlog
        # check file is valid
        try:
            f = open(fname, 'a+')
            f.close()
        except IOError:
            print "File/path not valid"
            start()

        list_radios()

        lradio = get_lradio()

        while not lradio:
            lradio = get_lradio()

        rname = get_rname(int(lradio) - 1)
        if lradio in log_active:
            print "Logging already active on " + rname
        else:
            tlog = int(raw_input("Enter a polling interval (seconds) :"))
            p = threading.Thread(target=log, args=(lradio, tlog, fname))
            p.setDaemon(True)
            p.start()
            log_active.append(lradio)
        start()

    elif data == "sync":
        sync_result = sync()
        print sync_result
        start()


    elif data == "h" or data == "help":
        prompt()
        start()


    elif data == "q" or data == "quit":
        rx = connect("quit")
        print "Server says: %s " % rx

    else:
        #prompt()
        start()


def get_all():
    num = get_rnum()
    global radio
    print "There are currently %d radios connected." % num
    print "=" * 33
    for i in range(0, num):
        r = get_rname(i)
        n = "".join(("r", str(i + 1)))
        freq = connect("getfreq" + " " + n)
        mode = connect("getmode" + " " + str(n))
        smeter = connect("getsmeter" + " " + str(n))
        preamp = connect("getpreamp" + " " + str(n))
        att = connect("getatt" + " " + str(n))

        print "Status of Radio %d (%s) \r\n" % (i + 1, r)
        print "Frequency : %s kHz" % freq
        print "Mode: %s" % mode
        print "S-Meter: %sdBm" % smeter
        print "Preamp = %s" % preamp
        print "Attenuator = %s " % att
        print "=" * 33

    print ""


def log(p, t, f):
    print "\n\n"
    tlog = t
    sradio = get_rname(int(p) - 1)

    sr = "".join(("r", str(p)))
    while True:
        try:
            frequency = connect("getfreq" + " " + sr + "\n")
            smeter = connect("getsmeter" + " " + sr + "\n")
            mode = connect("getmode" + " " + sr + "\n")
            write_file(f, sradio, mode, frequency, smeter)
            time.sleep(tlog)
        finally:
            pass


def get_mradio():
    num = get_rnum()

    mradio = raw_input("Choose Master radio number from the list: ").strip()

    if not mradio:
        print "Please select a radio"
        return False
    elif int(mradio) > num:
        print "Selected radio not recognized"
        return False

    else:

        return mradio


def get_sradio():
    num = get_rnum()
    sradio = raw_input("Choose Slave radio number from the list: ").strip()

    if not sradio:
        print "Please select a radio"
        return False
    elif int(sradio) > num:
        print "Selected radio not recognized"
        return False

    else:

        return sradio


def sync():
    num = get_rnum()
    print ""
    print "Set SLAVE to the same Frequency and Mode as MASTER.\r\n"
    print "Currently connected radios are:"
    for i in range(0, num):
        r = get_rname(i)
        print "%d is %s" % (i + 1, r)

    mradio = get_mradio()
    while not mradio:
        mradio = get_mradio()

    sradio = get_sradio()
    while not sradio:
        sradio = get_sradio()
    sr = "".join(("r", sradio))
    mr = "".join(("r", mradio))
    mfreq = connect("getfreq" + " " + mr)
    mmode = connect("getmode" + " " + mr)

    sfreq = connect("setfreq" + " " + mfreq + " " + sr)
    smode = connect("setmode" + " " + mmode + " " + sr)

    return (sfreq + "\r\n" + smode + "\r\n")


# Try to send and receive in one-go, to prevent the logging thread and the main prog
# getting the wrong receive data

def connect(data):
    try:
        lock.acquire()
        global sock
        sock.sendall(data + "\n")
        received = sock.recv(2048)
    finally:
        lock.release()

    return received


def write_file(fname, rname, mode, freq, smeter):
    filename = fname
    f = open(filename, 'a+')
    timenow = time.strftime("%d/%m/%Y %H:%M:%S", time.gmtime(time.time()))
    log = " ".join((timenow, rname, mode, freq, smeter, "\r\n"))
    f.write(log)
    f.close()


make_con()

lock = threading.Lock()
get_all()
print "Please choose a radio\r\n"
radio_num, rname = set_radio()
while not radio_num:
    radio_num, rname = set_radio()

prompt()
start()

</file>

++++

=== Example session ===

<code bash>
There are currently 3 radios connected.
=================================
Status of Radio 1 (IC-R75) 

Frequency : 2187.500 kHz
Mode: DATA
S-Meter: -114.2dBm
Preamp = 0
Attenuator = 0 
=================================
Status of Radio 2 (IC-M710) 

Frequency : 16804.500 kHz
Mode: DATA
S-Meter: -120.0dBm
Preamp = None
Attenuator = None 
=================================
Status of Radio 3 (AR7030) 

Frequency : 2182.000 kHz
Mode: USB
S-Meter: -110.3dBm
Preamp = 0
Attenuator = 0 
=================================

Please choose a radio

There are currently 3 radios connected.
Radio 1 is IC-R75
Radio 2 is IC-M710
Radio 3 is AR7030
Choose a radio number from the list : 3

The available commands are:
lr   : List Radios
sr   : Select the Radio to control
gr   : Get currently selected Radio name
gm   : Get Mode
sm   : Set Mode
gf   : Get Freq
sf   : Set Freq
gs   : Get S-meter
gp   : Get Pre-amp
pon  : Set Pre-amp On
p2on : Set Pre-amp 2 On
poff : Set Pre-amp Off
gatt : Get Attn
aton : Set Attn On
atoff: Set Attn Off
ga   : Get All (status of all radios)
sync : Sync freq/mode on two radios
log  : Setup background logging to file
h    : Help (show this command list)
q    : quit

AR7030 (2182.000 USB)  > sf 5680
AR7030 replied: Freq Set
AR7030 (5680.000 USB)  > 

</code>


===== GUI Client =====

{{:public:radio:screenshot_2022-07-24_15.04.52.png?direct&300 |}}
==== No S-meter version ====


++++ gui_nosmeter.py |

<file python gui_nosmeter.py>
# # new class-based gui

from Tkinter import *
import socket
import threading
import time



class Network(object):
    def __init__(self):
        self.sock = self.make_con()
        
    def make_con(self):
        self.sock = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
        self.sock.connect(("192.168.21.107", 9999))
        return self.sock

    def connect(self, data):
        try:
            lock.acquire()
            self.sock.sendall(data + "\n")
            self.received = self.sock.recv(2048)
        finally:
            lock.release()
            return self.received
            
class Dash(object):
    def __init__(self, master):
        self.master = master
        
        self.s = (n1.sock.getsockname())
        self.p = (n1.sock.getpeername())
        
        
        
        dash_frame = Toplevel(master, borderwidth = 2, relief = GROOVE, bg = 'black')
        dash_frame.title("Server")
        dash_frame.protocol("WM_DELETE_WINDOW", self.handler)
        dash_frame.resizable(0, 0)
        dash_frame.geometry("300x150+10-10")
        dash_frame.grid()
        
        #self.utc_time = StringVar()
        #Label(dash_frame, textvariable = self.utc_time, fg = 'green', bg = 'black').grid(row = 0, column = 0, sticky = W)
        
        Label(dash_frame, text = self.s, bg = 'black', fg = 'white').grid(row = 1, column = 0, sticky = W)
        
        Label(dash_frame, text = " < --- > ", bg = 'black', fg = 'white').grid(row = 1, column = 1)
        
        Label(dash_frame, text = self.p, bg = 'black', fg = 'white').grid(row = 1, column = 2, sticky = E)
         
        self.server_msg_l = StringVar()
        Label(dash_frame, textvariable = self.server_msg_l, fg = 'yellow', bg = 'black').grid(row = 2, column = 0, columnspan = 3, sticky = W)
        
        q_button = Button(dash_frame, text = "Quit", command = lambda: close())
        q_button.grid(row = 3, column = 0, sticky = W)
    
    def handler(self):
        pass
        
    def up_dash(self):
        self.server_msg = n1.connect("ident")
        self.server_msg_l.set(self.server_msg)
        #self.utc_time.set(time.strftime("%d/%m/%Y %H:%M", time.gmtime(time.time())))
        return

class nRadio(object):
    def __init__(self, master, radio):
        self.master = master
        
        self.radio = radio
        self.num = "".join(("r", self.radio))
       
        
        radio_frame = Frame(master, borderwidth=2, relief=GROOVE)
        
        radio_frame.grid()
        self.smeter_list = []

        Label(radio_frame, text="Name", width=10).grid(row=0, column=0)
        Label(radio_frame, text="Freq/kHz", width=10).grid(row=0, column=1)
        Label(radio_frame, text="Mode", width=10).grid(row=0, column=2)
        #Label(radio_frame, text="Signal/dBm", width=10).grid(row=0, column=3)
        #Label(radio_frame, text="Max/dBm", width=10, fg='red').grid(row=0, column=4)
        #Label(radio_frame, text="Ave/dBm", width=10, fg='green').grid(row=0, column=5)
        #Label(radio_frame, text="Min/dBm", width=10, fg='blue').grid(row=0, column=6)

        self.name_l = StringVar()
        self.l_name = Label(radio_frame, textvariable=self.name_l, width=10)
        self.l_name.grid(row=1, column=0, sticky=W)
        
        self.freq_l = StringVar()
        self.l_freq = Label(radio_frame, fg='red', textvariable=self.freq_l, width=10)
        self.l_freq.grid(row=1, column=1, sticky=E)
        
        self.mode_l = StringVar()
        self.l_mode = Label(radio_frame, textvariable=self.mode_l, width=10)
        self.l_mode.grid(row=1, column=2, sticky=E)
        '''
        self.e_mode = Entry(radio_frame, width=10, bg = 'white', fg = 'black', insertbackground = 'blue')
        self.e_mode.grid(row=2, column=2)
        self.e_mode.bind('<Return>', (lambda event: self.set_mode(self.num)))
        '''
        #self.e_mode = StringVar()
        self.b_mode_usb = Button(radio_frame, text = "USB", width = 4, command = lambda: self.set_mode("usb", self.num))
        self.b_mode_usb.grid(row = 3, column = 0)
        
        self.b_mode_lsb = Button(radio_frame, text = "LSB", width = 4, command = lambda: self.set_mode("lsb", self.num))
        self.b_mode_lsb.grid(row = 3, column = 1)
        
        self.b_mode_cw = Button(radio_frame, text = "CW", width = 4, command = lambda: self.set_mode("cw", self.num))
        self.b_mode_cw.grid(row = 4, column = 0)
        
        self.b_mode_am = Button(radio_frame, text = "AM", width = 4, command = lambda: self.set_mode("am", self.num))
        self.b_mode_am.grid(row = 4, column = 1)
        
        self.b_mode_data = Button(radio_frame, text = "Data", width = 4, command = lambda: self.set_mode("data", self.num))
        self.b_mode_data.grid(row = 3, column = 2)

        self.b_qsy_up = Button(radio_frame, text = "+1kHz", width = 6, command = lambda: self.qsy_up( self.num))
        self.b_qsy_up.grid(row = 3, column = 3)

        self.b_qsy_down = Button(radio_frame, text = "-1kHz", width = 6, command = lambda: self.qsy_down( self.num))
        self.b_qsy_down.grid(row = 4, column = 3)

        self.b_update = Button(radio_frame, text = "Get", width = 6, command = lambda:self.get_all())
        self.b_update.grid(row = 0, column = 3)
        
        
        self.smeter_l = StringVar()
        self.l_smeter = Label(radio_frame, textvariable=self.smeter_l, width=10)
        #self.l_smeter.grid(row=1, column=3, sticky=E)

        self.max_var = StringVar()
        self.l_max = Label(radio_frame, textvariable=self.max_var, width=10)
        #self.l_max.grid(row=1, column=4)
        
        self.ave_var = StringVar()
        self.l_average = Label(radio_frame, textvariable=self.ave_var, width=10)
        #self.l_average.grid(row=1, column=5)

        self.min_var = StringVar()
        self.l_min = Label(radio_frame, textvariable=self.min_var, width=10)
        #self.l_min.grid(row=1, column=6)

        self.e_freq = Entry(radio_frame, width=10, bg = 'white', fg = 'black', insertbackground = 'blue')
        self.e_freq.grid(row=2, column=1)
        self.e_freq.focus()
        self.e_freq.bind('<Return>', (lambda event: self.set_freq(self.num)))
        
        
        
        self.pre = IntVar()
        self.cb_pre = Checkbutton(radio_frame, variable=self.pre, command=lambda: self.preamp_onoff(self.num))
        self.cb_pre.grid(row=5, column=3, sticky=E)

        self.l_pre = Label(radio_frame, width=10, text="Preamp")
        self.l_pre.grid(row=5, column=2, sticky=W)

        self.att = IntVar()
        self.cb_att = Checkbutton(radio_frame, variable=self.att, command=lambda: self.att_onoff(self.num))
        self.cb_att.grid(row=6, column=3, sticky=E)
        
        self.l_att = Label(radio_frame, width=10, text="Att")
        self.l_att.grid(row=6, column=2, sticky=W)
        
        self.set_log = IntVar()
        self.cb_log = Checkbutton(radio_frame, variable = self.set_log)
        #self.cb_log.grid(row = 6, column = 1, sticky = W)
        
        self.l_log = Label(radio_frame, width = 10, text = "Log to file...")
        #self.l_log.grid(row = 6, column = 0, sticky = E)

        self.c1 = Canvas(radio_frame, width=260, height=100, bg='black')
        #self.c1.grid(row=2, column=3, columnspan=4, rowspan=3)

        name = self.get_name(radio)
       

    def get_all(self):
        
        self.get_freq(self.num)
        self.get_mode(self.num)
        #self.get_smeter(self.num)
        self.get_preamp(self.num)
        self.get_atten(self.num)
        #self.graph_points()       
        #self.avg()
        #self.max()
        #self.min()
        
        if self.set_log.get() == 1:
            if int(time.time()) % 10.0 == 0:
                self.write_file()
        return
        
    def get_freq(self, radio):

        self.freq = n1.connect("getfreq" + " " + radio)
        self.freq_l.set(self.freq)
        return

    def set_freq(self, radio):
        self.freq = str(self.e_freq.get())
        self.newfreq = n1.connect("setfreq" + " " + self.freq + " " + radio)
        self.e_freq.delete(0, END)
        self.get_all()
        return

    def qsy_up(self,radio):
        
        oldf = n1.connect("getfreq" + " " + radio)
        newf = str(float(oldf) + 1)
        freq = n1.connect("setfreq" + " " + newf + " " + radio)
        self.get_all()
        return

    def qsy_down(self,radio):
        oldf = n1.connect("getfreq" + " " + radio)
        newf = str(float(oldf) - 1)
        freq = n1.connect("setfreq" + " " + newf + " " + radio)
        self.get_all()
        return

    def get_mode(self, radio):
        self.mode = n1.connect("getmode" + " " + radio)
        self.mode_l.set(self.mode)
        return

    def set_mode(self, mode, radio):
        #self.mode = str(self.e_mode.get())
        self.newmode = n1.connect("setmode" + " " + mode + " " + radio)
        #self.e_mode.delete(0, END)
        self.get_all()
        return

    def get_smeter(self, radio):
        self.smeter = n1.connect("getsmeter" + " " + radio)
        self.smeter_l.set(self.smeter)
        self.smeter_list.append(float(self.smeter))
        if len(self.smeter_list) > 120:
            self.smeter_list.pop(0)
        return

    def avg(self):
        s = self.smeter_list
        total = 0
        for i in s:
            total += i
        self.av = round((total / len(s)), 1)
        self.ave_var.set(str(self.av))
        self.c1.create_line(0, 100 - (self.av + 123 + 5), 310, 100 - (self.av + 123 + 5), fill="green")
        return self.av

    def min(self):
        s = self.smeter_list
        self.mn = s[0]
        for i in s:
            if i < self.mn:
                self.mn = i
        self.min_var.set(str(self.mn))
        self.c1.create_line(0, 100 - (self.mn + 123 + 5), 310, 100 - (self.mn + 123 + 5), fill="blue")
        return self.mn

    def max(self):
        s = self.smeter_list
        self.mx = s[0]
        for i in s:
            if i > self.mx:
                self.mx = i
        self.max_var.set(str(self.mx))
        self.c1.create_line(0, 100 - (self.mx + 123 + 5), 310, 100 - (self.mx + 123 + 5), fill="red")
        return self.mx

    def get_preamp(self, radio):
        self.preamp = n1.connect("getpreamp" + " " + radio)
        if self.preamp == "1":
            self.cb_pre.select()
        elif self.preamp == "0":
            self.cb_pre.deselect()
        return

    def preamp_onoff(self, radio):
        self.prestate = self.pre.get()
        if self.prestate:
            n1.connect("preampon" + " " + radio)
        else:
            n1.connect("preampoff" + " " + radio)
        self.get_all()
        return

    def att_onoff(self, radio):
        self.attstate = self.att.get()
        if self.attstate:
            n1.connect("atton" + " " + radio)
        else:
            n1.connect("attoff" + " " + radio)
        self.get_all()
        return


    def get_atten(self, radio):
        self.atten = n1.connect("getatt" + " " + radio)
        if self.atten == "1":
            self.cb_att.select()
        elif self.atten == "0":
            self.cb_att.deselect()
        return

    def get_name(self, radio):
        print radio
        self.all_names = n1.connect("listradios")
        self.radios = self.all_names.split()
        print self.radios
        self.name = self.radios[int(radio) - 1]
        self.name_l.set(self.name)
        return

    def graph_points(self):
        seq = self.smeter_list
        y_stretch = 1
        y_gap = 5
        x_stretch = 0
        x_width = 2
        x_gap = 2
        height = 100
        self.c1.delete(ALL)
        self.c1.create_line(0, 100 - (-73 + 123 + 5), 310, 100 - (-73 + 123 + 5), fill='white')
        for x, y in enumerate(seq):
            yd = y + 123
            x0 = x * x_stretch + x * x_width + x_gap
            y0 = height - (yd * y_stretch + y_gap)
            x1 = x * x_stretch + x * x_width + x_width + x_gap
            y1 = height - y_gap
            self.c1.create_rectangle(x0, y0, x1, y1, fill="yellow")

    def write_file(self):
        self.filename = self.name+".txt"
        self.f = open(self.filename, 'a+')
        timenow = time.strftime("%d/%m/%Y %H:%M:%S", time.gmtime(time.time()))
        log = " ".join((timenow, self.name, self.mode, self.freq, self.smeter, self.preamp, self.atten, "\r\n"))
        self.f.write(log)
        self.f.close()

def update():
    #loops = 0

    try:
        nRadio1.get_all()
    except:
        pass
    try:
        nRadio2.get_all()
    except:
        pass
    try:
        nRadio3.get_all()
    except:
        pass
    try:
        nRadio4.get_all()
    except:
        pass
    d1.up_dash()
    return

def main():
    #loops = 0
    while True:
        try:
            nRadio1.get_all()
        except:
            pass
        try:
            nRadio2.get_all()
        except:
            pass
        try:
            nRadio3.get_all()
        except:
            pass
        try:
            nRadio4.get_all()
        except:
            pass
        d1.up_dash()
        #loops += 1
        #print threading.currentThread().name, loops
        time.sleep(5)

def close():
    n1.connect("quit")
    root.destroy()
    
    
if __name__ == "__main__":
    version = "v0.4"
    lock = threading.Lock()
    root = Tk()
    #w, h = root.winfo_screenwidth(), root.winfo_screenheight()
    #root.geometry("%dx%d+0+0" % (w, h))
    #root.geometry("300x520+0+0")
    root.title("Netradio " + version)
    #root.withdraw()
    n1 = Network()
    #radio_count = (n1.connect("count"))
    #radio_count = 3
    
    radio_count = int(n1.connect("count"))
    if radio_count > 0:
        nRadio1 = nRadio(root, "1")
    if radio_count > 1:
        nRadio2 = nRadio(root, "2")
    if radio_count > 2:
        nRadio3 = nRadio(root, "3")
    if radio_count > 3:
        nRadio4 = nRadio(root, "4")
        
    d1 = Dash(root)
    
    #print threading.currentThread().name
    #m1 = threading.Thread(target = main)
    #m1.setDaemon(True)
    #m1.start()
    
    update()
    
    root.mainloop()
    
    
    
    

</file>

++++

{{:public:radio:screenshot_2022-07-24_16.14.06.png?direct&200 |}}



==== S-meter display version ====


++++ gui.py |

<file python gui.py>
# # new class-based gui

from Tkinter import *
import socket
import threading
import time



class Network(object):
    def __init__(self):
        self.sock = self.make_con()
        
    def make_con(self):
        self.sock = socket.socket(socket.AF_INET, socket.SOCK_STREAM)
        self.sock.connect(("192.168.21.107", 9999))
        return self.sock

    def connect(self, data):
        try:
            lock.acquire()
            self.sock.sendall(data + "\n")
            self.received = self.sock.recv(2048)
        finally:
            lock.release()
            return self.received
            
class Dash(object):
    def __init__(self, master):
        self.master = master
        
        self.s = (n1.sock.getsockname())
        self.p = (n1.sock.getpeername())
        
        
        
        dash_frame = Toplevel(master, borderwidth = 2, relief = GROOVE, bg = 'black')
        dash_frame.title("Server")
        dash_frame.protocol("WM_DELETE_WINDOW", self.handler)
        dash_frame.resizable(0, 0)
        dash_frame.geometry("300x150-10+10")
        dash_frame.grid()
        
        self.utc_time = StringVar()
        Label(dash_frame, textvariable = self.utc_time, fg = 'green', bg = 'black').grid(row = 0, column = 0, sticky = W)
        
        Label(dash_frame, text = self.s, bg = 'black', fg = 'white').grid(row = 1, column = 0, sticky = W)
        
        Label(dash_frame, text = " < --- > ", bg = 'black', fg = 'white').grid(row = 1, column = 1)
        
        Label(dash_frame, text = self.p, bg = 'black', fg = 'white').grid(row = 1, column = 2, sticky = E)
         
        self.server_msg_l = StringVar()
        Label(dash_frame, textvariable = self.server_msg_l, fg = 'yellow', bg = 'black').grid(row = 2, column = 0, columnspan = 3, sticky = W)
        
        q_button = Button(dash_frame, text = "Quit", command = lambda: close())
        q_button.grid(row = 3, column = 0, sticky = W)
    
    def handler(self):
        pass
        
    def up_dash(self):
        self.server_msg = n1.connect("ident")
        self.server_msg_l.set(self.server_msg)
        self.utc_time.set(time.strftime("%d/%m/%Y %H:%M", time.gmtime(time.time())))
        return

class nRadio(object):
    def __init__(self, master, radio):
        self.master = master
        
        self.radio = radio
        self.num = "".join(("r", self.radio))
       
        
        radio_frame = Frame(master, borderwidth=2, relief=GROOVE)
        
        radio_frame.grid()
        self.smeter_list = []

        Label(radio_frame, text="Name", width=10).grid(row=0, column=0)
        Label(radio_frame, text="Freq/kHz", width=10).grid(row=0, column=1)
        Label(radio_frame, text="Mode", width=10).grid(row=0, column=2)
        Label(radio_frame, text="Signal/dBm", width=10).grid(row=0, column=3)
        Label(radio_frame, text="Max/dBm", width=10, fg='red').grid(row=0, column=4)
        Label(radio_frame, text="Ave/dBm", width=10, fg='green').grid(row=0, column=5)
        Label(radio_frame, text="Min/dBm", width=10, fg='blue').grid(row=0, column=6)

        self.name_l = StringVar()
        self.l_name = Label(radio_frame, textvariable=self.name_l, width=10)
        self.l_name.grid(row=1, column=0, sticky=W)
        
        self.freq_l = StringVar()
        self.l_freq = Label(radio_frame, fg='red', textvariable=self.freq_l, width=10)
        self.l_freq.grid(row=1, column=1, sticky=E)
        
        self.mode_l = StringVar()
        self.l_mode = Label(radio_frame, textvariable=self.mode_l, width=10)
        self.l_mode.grid(row=1, column=2, sticky=E)
        '''
        self.e_mode = Entry(radio_frame, width=10, bg = 'white', fg = 'black', insertbackground = 'blue')
        self.e_mode.grid(row=2, column=2)
        self.e_mode.bind('<Return>', (lambda event: self.set_mode(self.num)))
        '''
        #self.e_mode = StringVar()
        self.b_mode_usb = Button(radio_frame, text = "USB", width = 4, command = lambda: self.set_mode("usb", self.num))
        self.b_mode_usb.grid(row = 3, column = 0)
        
        self.b_mode_lsb = Button(radio_frame, text = "LSB", width = 4, command = lambda: self.set_mode("lsb", self.num))
        self.b_mode_lsb.grid(row = 3, column = 1)
        
        self.b_mode_cw = Button(radio_frame, text = "CW", width = 4, command = lambda: self.set_mode("cw", self.num))
        self.b_mode_cw.grid(row = 4, column = 0)
        
        self.b_mode_am = Button(radio_frame, text = "AM", width = 4, command = lambda: self.set_mode("am", self.num))
        self.b_mode_am.grid(row = 4, column = 1)
        
        self.b_mode_data = Button(radio_frame, text = "Data", width = 4, command = lambda: self.set_mode("data", self.num))
        self.b_mode_data.grid(row = 3, column = 2)
        
        self.smeter_l = StringVar()
        self.l_smeter = Label(radio_frame, textvariable=self.smeter_l, width=10)
        self.l_smeter.grid(row=1, column=3, sticky=E)

        self.max_var = StringVar()
        self.l_max = Label(radio_frame, textvariable=self.max_var, width=10)
        self.l_max.grid(row=1, column=4)
        
        self.ave_var = StringVar()
        self.l_average = Label(radio_frame, textvariable=self.ave_var, width=10)
        self.l_average.grid(row=1, column=5)

        self.min_var = StringVar()
        self.l_min = Label(radio_frame, textvariable=self.min_var, width=10)
        self.l_min.grid(row=1, column=6)

        self.e_freq = Entry(radio_frame, width=10, bg = 'white', fg = 'black', insertbackground = 'blue')
        self.e_freq.grid(row=2, column=1)
        self.e_freq.focus()
        self.e_freq.bind('<Return>', (lambda event: self.set_freq(self.num)))
        
        
        
        self.pre = IntVar()
        self.cb_pre = Checkbutton(radio_frame, variable=self.pre, command=lambda: self.preamp_onoff(self.num))
        self.cb_pre.grid(row=5, column=4, sticky=E)

        self.l_pre = Label(radio_frame, width=10, text="Preamp")
        self.l_pre.grid(row=5, column=3, sticky=W)

        self.att = IntVar()
        self.cb_att = Checkbutton(radio_frame, variable=self.att, command=lambda: self.att_onoff(self.num))
        self.cb_att.grid(row=6, column=4, sticky=E)
        
        self.l_att = Label(radio_frame, width=10, text="Att")
        self.l_att.grid(row=6, column=3, sticky=W)
        
        self.set_log = IntVar()
        self.cb_log = Checkbutton(radio_frame, variable = self.set_log)
        self.cb_log.grid(row = 6, column = 1, sticky = W)
        
        self.l_log = Label(radio_frame, width = 10, text = "Log to file...")
        self.l_log.grid(row = 6, column = 0, sticky = E)

        self.c1 = Canvas(radio_frame, width=260, height=100, bg='black')
        self.c1.grid(row=2, column=3, columnspan=4, rowspan=3)

        name = self.get_name(radio)
       

    def get_all(self):
        
        self.get_freq(self.num)
        self.get_mode(self.num)
        self.get_smeter(self.num)
        self.get_preamp(self.num)
        self.get_atten(self.num)
        self.graph_points()       
        self.avg()
        self.max()
        self.min()
        
        if self.set_log.get() == 1:
            if int(time.time()) % 10.0 == 0:
                self.write_file()
        return
        
    def get_freq(self, radio):

        self.freq = n1.connect("getfreq" + " " + radio)
        self.freq_l.set(self.freq)
        return

    def set_freq(self, radio):
        self.freq = str(self.e_freq.get())
        self.newfreq = n1.connect("setfreq" + " " + self.freq + " " + radio)
        self.e_freq.delete(0, END)
        
        return

    def get_mode(self, radio):
        self.mode = n1.connect("getmode" + " " + radio)
        self.mode_l.set(self.mode)
        return

    def set_mode(self, mode, radio):
        #self.mode = str(self.e_mode.get())
        self.newmode = n1.connect("setmode" + " " + mode + " " + radio)
        #self.e_mode.delete(0, END)
        return

    def get_smeter(self, radio):
        self.smeter = n1.connect("getsmeter" + " " + radio)
        self.smeter_l.set(self.smeter)
        self.smeter_list.append(float(self.smeter))
        if len(self.smeter_list) > 120:
            self.smeter_list.pop(0)
        return

    def avg(self):
        s = self.smeter_list
        total = 0
        for i in s:
            total += i
        self.av = round((total / len(s)), 1)
        self.ave_var.set(str(self.av))
        self.c1.create_line(0, 100 - (self.av + 123 + 5), 310, 100 - (self.av + 123 + 5), fill="green")
        return self.av

    def min(self):
        s = self.smeter_list
        self.mn = s[0]
        for i in s:
            if i < self.mn:
                self.mn = i
        self.min_var.set(str(self.mn))
        self.c1.create_line(0, 100 - (self.mn + 123 + 5), 310, 100 - (self.mn + 123 + 5), fill="blue")
        return self.mn

    def max(self):
        s = self.smeter_list
        self.mx = s[0]
        for i in s:
            if i > self.mx:
                self.mx = i
        self.max_var.set(str(self.mx))
        self.c1.create_line(0, 100 - (self.mx + 123 + 5), 310, 100 - (self.mx + 123 + 5), fill="red")
        return self.mx

    def get_preamp(self, radio):
        self.preamp = n1.connect("getpreamp" + " " + radio)
        if self.preamp == "1":
            self.cb_pre.select()
        elif self.preamp == "0":
            self.cb_pre.deselect()
        return

    def preamp_onoff(self, radio):
        self.prestate = self.pre.get()
        if self.prestate:
            n1.connect("preampon" + " " + radio)
        else:
            n1.connect("preampoff" + " " + radio)
        return

    def att_onoff(self, radio):
        self.attstate = self.att.get()
        if self.attstate:
            n1.connect("atton" + " " + radio)
        else:
            n1.connect("attoff" + " " + radio)
        return


    def get_atten(self, radio):
        self.atten = n1.connect("getatt" + " " + radio)
        if self.atten == "1":
            self.cb_att.select()
        elif self.atten == "0":
            self.cb_att.deselect()
        return

    def get_name(self, radio):
        print radio
        self.all_names = n1.connect("listradios")
        self.radios = self.all_names.split()
        print self.radios
        self.name = self.radios[int(radio) - 1]
        self.name_l.set(self.name)
        return

    def graph_points(self):
        seq = self.smeter_list
        y_stretch = 1
        y_gap = 5
        x_stretch = 0
        x_width = 2
        x_gap = 2
        height = 100
        self.c1.delete(ALL)
        self.c1.create_line(0, 100 - (-73 + 123 + 5), 310, 100 - (-73 + 123 + 5), fill='white')
        for x, y in enumerate(seq):
            yd = y + 123
            x0 = x * x_stretch + x * x_width + x_gap
            y0 = height - (yd * y_stretch + y_gap)
            x1 = x * x_stretch + x * x_width + x_width + x_gap
            y1 = height - y_gap
            self.c1.create_rectangle(x0, y0, x1, y1, fill="yellow")

    def write_file(self):
        self.filename = self.name+".txt"
        self.f = open(self.filename, 'a+')
        timenow = time.strftime("%d/%m/%Y %H:%M:%S", time.gmtime(time.time()))
        log = " ".join((timenow, self.name, self.mode, self.freq, self.smeter, self.preamp, self.atten, "\r\n"))
        self.f.write(log)
        self.f.close()



def main():
    #loops = 0
    while True:
        try:
            nRadio1.get_all()
        except:
            pass
        try:
            nRadio2.get_all()
        except:
            pass
        try:
            nRadio3.get_all()
        except:
            pass
        try:
            nRadio4.get_all()
        except:
            pass
        d1.up_dash()
        #loops += 1
        #print threading.currentThread().name, loops
        time.sleep(1)

def close():
    n1.connect("quit")
    root.destroy()
    
    
if __name__ == "__main__":
    version = "v0.3"
    lock = threading.Lock()
    root = Tk()
    #w, h = root.winfo_screenwidth(), root.winfo_screenheight()
    #root.geometry("%dx%d+0+0" % (w, h))
    root.geometry("550x600+0+0")
    root.title("GM4SLV Radio Controller " + version)
    #root.withdraw()
    n1 = Network()
    #radio_count = (n1.connect("count"))
    #radio_count = 3
    
    radio_count = int(n1.connect("count"))
    if radio_count > 0:
        nRadio1 = nRadio(root, "1")
    if radio_count > 1:
        nRadio2 = nRadio(root, "2")
    if radio_count > 2:
        nRadio3 = nRadio(root, "3")
    if radio_count > 3:
        nRadio4 = nRadio(root, "4")
        
    d1 = Dash(root)
    
    #print threading.currentThread().name
    m1 = threading.Thread(target = main)
    m1.setDaemon(True)
    m1.start()
    

    
    root.mainloop()
    
    
    
    

    
</file>

++++

{{:public:radio:screenshot_2022-07-24_15.01.43.png?direct&200 |}}




===== Further Information =====


{{tag>}}