<-[[.:start]] ====== MB7AZE AllStar Config ====== ===== all /etc/asterisk files ===== {{ :private:greenmeadow:allstar_conf.tar |}} ===== Main Config files ===== ==== echolink.conf ==== ++++ /etc/asterisk/echolink.conf | [el0] call = MB7AZE-L ; Change this! pwd = xxxxxxxx ; Change this! name = John ; Change this! qth = allstar 481481 ; Change this! email = gm4slv@gm4slv.plus.com ; Change this! node = 879598 ; Change this! ; Data for EchoLink Status Page lat = 60.2883 ; Latitude in decimal degrees lon = -001.42533 ; Longitude in decimal degrees freq = 430.050 ; not mandatory Frequency in MHz tone = 0.0 ; not mandatory CTCSS Tone (0 for none) power = 1 ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts) height = 0 ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet) gain = 0 ; Gain in db (0-9) dir = 0 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction) maxstns = 5 ; Max Stations rtcptimeout = 10 recfile = /tmp/echolink_recorded.gsm ; astnode = 481481 ; Change this! context = radio-secure ; Default in code is echolink-in ; Max 3 servers server1 = nasouth.echolink.org server2 = naeast.echolink.org server3 = server3.echolink.org ; To deny w6xxx you would add the statement: deny = w6xxx ; To prohibit computer-based connections you would write: permit = *-* ; To allow access to only a select group of callsigns: permit = w6abc,w6def,... ; permit ; comma delimited list of callsign, type (-r) ; deny ; Remote text commands thru netcat: ; o.conip (request a connect) ; o.dconip (request a disconnect) ; o.rec (turn on/off recording) ; ipaddr ; port ++++ ==== manager.conf ==== ++++ /etc/asterisk/manager.conf | ; ; Asterisk Call Management support ; ; By default asterisk will listen on localhost only. [general] enabled = yes port = 5038 bindaddr = 127.0.0.1 [gm4slv] secret = llcgi read = all,system,call,log,verbose,command,agent,user,config write = all,system,call,log,verbose,command,agent,user,config ++++ ==== rpt.conf ==== ++++ /etc/asterisk/rpt.conf | ; Radio Repeater configuration file (for use with app_rpt) ; Your Repeater ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; ; This is where you define your nodes which can be connected to. ; [nodes] ; Note, if you are using automatic update for allstar link nodes, ; no allstar link nodes should be defined here. Only place a definition ; for your local nodes, and private (off of allstar link) nodes here. ;481480 = radio@127.0.0.1:4569/481480,NONE ; This must be changed to your node number 481481 = radio@127.0.0.1:4569/481481,NONE ; This must be changed to your node number ; and iax port number if not the default ;[481480] ; Change this to your assigned node number [481481] ; Change this to your assigned node number ; Must also be enabled in modules.conf ; Rx audio/signalling channel. Choose ONLY 1 per node stanza ; Enable the selected channel driver in modules.conf !!! ;rxchannel = dahdi/pseudo ; No radio (hub) rxchannel = SimpleUSB/usb_48148 ; SimpleUSB ; rxchannel = Pi/1 ; Raspberry Pi PiTA ; rxchannel = Radio/usb_48148 ; USBRadio (DSP) ; rxchannel = Dahdi/1 ; PCI Quad card ; rxchannel = Beagle/1 ; BeagleBoard ; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP ; rxchannel = Voter/48148 ; RTCM device duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time. ; Special Case: Full duplex if linktolink is set to yes. ; This mode is preferred when interfacing with an external multiport repeater controller. ; Comment out idrecording and idtalkover to suppress IDs also ; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio. ; This mode is preferred when interfacing a simplex node. ; 2 = Full Duplex with telemetry tones and hang time. ; This mode is preferred when interfacing a repeater. ; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio. ; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down. linktolink = no ; disables forcing physical half-duplex operation of main repeater while ; still keeping half-duplex semantics (optional) linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received. ; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db. ; If linkmongain set to a positive number monitored audio will increase by the set amount in db. ; The value of linkmongain is in db. The default value is 0 db. erxgain = -3 ; Echolink receive gain adjustment ; Note: Gain is in db-volts (20logVI/VO) etxgain = 3 ; Echolink transmit gain adjustment ; Note: Gain is in db-volts (20logVI/VO) eannmode = 2 ; 1 = Say only node number on echolink connects (default = 1) ; 2 = say phonetic call sign only on echolink connects ; 3 = say phonetic call sign and node number on echolink connects ;controlstates = controlstates ; system control state stanza scheduler = schedule ; scheduler stanza functions = functions ; Repeater Function stanza phone_functions = functions ; Phone Function stanza link_functions = functions ; Link Function stanza telemetry = telemetry ; Telemetry stanza morse = morse ; Morse stanza wait_times = wait-times ; Wait times stanza context = radio ; dialing context for phone callerid = "Repeater" <0000000000> ; callerid for phone calls accountcode = RADIO ; account code (optional) hangtime = 200 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms) althangtime = 300 ; longer squelch tail totime = 300000 ; 5 mins (12/4/22) transmit time-out time (in ms) (optional, default 3 minutes 180000 ms) telemnomdb = -3 ; telemduckdb = -10 ; ;idrecording = /home/gm4slv/gm4slv_id ;idrecording = /home/gm4slv/mb7aze_id idrecording = |iDE MB7AZE ; Main ID message ;idtalkover = |iMB7AZE ; Talkover ID message idtalkover = |iMB7AZE ; Talkover ID message ; See Telemetry section Example: idrecording = rpt/nodenames/48148 idtime = 900000 ; 15 mins (12/4/22) id interval time (in ms) (optional) Default 5 minutes (300000 ms) politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000) unlinkedct = ct12 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none) remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links) linkunkeyct = ct4 ; sent when a transmission received over the link unkeys ;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC). ; Supermon smlogger connpgm=/usr/local/sbin/supermon/smlogger 1 discpgm=/usr/local/sbin/supermon/smlogger 0 ;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being connected to us (them) ;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default) ; passes 2 command line arguments to your program: ; 1. node number in this stanza (us) ; 2. node number being disconnected from us (them) lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only. lnkacttime = 3600 ; Link activity timer time in seconds. lnkactmacro = *73 ; Function to execute when link activity timer expires. lnkacttimerwarn = custom/timeout ; Message to play when the link activity timer has 30 seconds left. ;remote_inact_timeout = 60 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60) ;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60) ;remote_timeout_warning_freq = ; 30 ;remote_timeout_warning = ; (3 * 60) ;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays. holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes ; except when an ID needs to be done and there is a signal coming from a connected node. telemdefault = 1 ; 0 = telemetry output off ; 1 = telemetry output on (default = 1) ; 2 = timed telemetry output on command execution and for a short time thereafter. telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command, ; 1 = Allow users to change the setting with a COP command. (default = 1) beaconing = 1 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US) parrotmode = 1 ; 0 = Parrot Off (default = 0) ; 1 = Parrot On Command ; 2 = Parrot Always ; 3 = Parrot Once by Command parrottime = 1000 ; Set the amount of time in milliseconds ; to wait before parroting what was received ;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified ; b/w. app_rpt must have been compiled with ; the notch option startup_macro = *80*81*70 ; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory ; Stream your node audio to Broadcastify or similar. See https://wiki.allstarlink.org/wiki/Stream_Node_Audio_to_Broadcastify ; outstreamcmd = /bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - | /usr/bin/ezstream -qvc /etc/ezstream.xml ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Need more information on these ;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional) ;extnodefile = /home/gm4slv/rpt_extnodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional) ;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes???? ;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames ;archivedir = /tmp ; defines and enables activity recording into specified directory (optional) ;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full) ; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set ; ; to support tail messages. They can be omitted otherwise. ;tailmessagetime = 300000 ; Play a tail message every 5 mins ;tailsquashedtime = 30000 ; If squashed by another user, ; ; try again after 30 seconds ;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message ; alt_functions ; ctgroup ; dphone_functions ; idtime ; iobase ; iospeed ; locallist ; mars Remote Base ; memory ; nobusyout ; nodes ; nolocallinkct ; notelemtx ; outxlat ; parrot ; propagate_phonedtmf ; rptnode ; rptinactmacro Macro to execute when inactivity timer expires ; rptinacttime Inactivity timer time in seconds (0 seconds disables feature) ; rxnotch Optional Audio notch ; simplexphonedelay ; tonemacro ; tonezone ; txlimits ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; *** Status Reporting *** ; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org statpost_url = http://stats.allstarlink.org/uhandler ; Status updates [functions] ; Prefix Functions ; *1 Disconnect Link ; *2 Monitor Link ; *3 Connect Link ; *4 Command Mode ; *5 Macros ; *6 User Functions ; *7 Connection Status/Functions ; *8 User Functions ; *9 User Functions ; *0 User Functions ; *A User Functions ; *B User Functions ; *C User Functions ; *D User Functions ; Mandatory Command Codes 1 = ilink,1 ; Disconnect specified link 2 = ilink,2 ; Connect specified link -- monitor only 3 = ilink,3 ; Connect specified link -- tranceive 4 = ilink,4 ; Enter command mode on specified link 70 = ilink,5 ; System status ;99 = cop,6 ; PTT (phone mode only) ; End Mandatory Command Codes 73 = ilink,6 ; Disconnect All Links 74 = ilink,16 ; Reconnect links disconnected with "disconnect all links" 80 = status,11 ; Force ID (local only) 81 = status,12 ; Give Time of Day (local only) 91 = cop,21 ; Enable Parrot Mode 92 = cop,22 ; Disable Parrot Mode 93 = cop,55 ; Parrot Once if parrot mode is disabled 98 = cop,2 ; System enable 99 = cop,3 ; System disable 901 = cop,1 ; System warm boot ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Macro Commands 5 = macro ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Autopatch Commands ; Note, This may be a good place for other 2 digit frequently used commands ;61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up ;62 = autopatchdn ; Autopatch down ; autopatchup can optionally take comma delimited setting=value pairs: ; context = string ; Override default context with "string" ; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second) ; farenddisconnect = 1 ; Automatically disconnect when called party hangs up ; noct = 1 ; Don't send repeater courtesy tone during autopatch calls ; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up ; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Status Commands ; 1 - Force ID (global) ; 2 - Give Time of Day (global) ; 3 - Give software Version (global) ; 4 - Give GPS location info ; 5 - Last (dtmf) user ; 11 - Force ID (local only) ; 12 - Give Time of Day (local only) ;721 = status,1 ; Force ID (global) ;722 = status,2 ; Give Time of Day (global) ;723 = status,3 ; Give software Version (global) ;724 = status,4 ; Give GPS location info ;725 = status,5 ; Last (dtmf) user ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Link Commands ; 1 - Disconnect specified link ; 2 - Connect specified link -- monitor only ; 3 - Connect specified link -- tranceive ; 4 - Enter command mode on specified link ; 5 - System status ; 6 - Disconnect all links ; 7 - Last Node to Key Up ; 8 - Connect specified link -- local monitor only ; 9 - Send Text Message (9,,Message Text, etc. ; 10 - Disconnect all RANGER links (except permalinks) ; 11 - Disconnect a previously permanently connected link ; 12 - Permanently connect specified link -- monitor only ; 13 - Permanently connect specified link -- tranceive ; 15 - Full system status (all nodes) ; 16 - Reconnect links disconnected with "disconnect all links" ; 17 - MDC test (for diag purposes) ; 18 - Permanently Connect specified link -- local monitor only ; ilink commands 1 through 5 are defined in the Mandatory Command section ;806 = ilink,6 ; Disconnect all links ;827 = ilink,7 ; Last Node to Key Up ;808 = ilink,8 ; Connect specified link -- local monitor only ;809 = ilink,9,48148,"Testing" ; would send a text message to node 48148 replace 48148 with 0 for all connected nodes ;810 = ilink,10 ; Disconnect all RANGER links (except permalinks) ;811 = ilink,11 ; Disconnect a previously permanently connected link ;812 = ilink,12 ; Permanently connect specified link -- monitor only ;823 = ilink,13 ; Permanently connect specified link -- tranceive ;815 = ilink,15 ; Full system status (all nodes) ;817 = ilink,17 ; MDC test (for diag purposes) ;818 = ilink,18 ; Permanently Connect specified link -- local monitor only ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;; ; Control operator (cop) functions. ; Change these to something other than these codes listed below! ; Uncomment as needed. ;901 = cop,1 ; System warm boot ; 904 = cop,4 ; Test tone on/off (toggle) ; 905 = cop,5 ; Dump system variables on console (debug use only) ; 907 = cop,7 ; Time out timer enable ; 908 = cop,8 ; Time out timer disable ; 909 = cop,9 ; Autopatch enable ; 910 = cop,10 ; Autopatch disable ; 911 = cop,11 ; User linking functions enable ; 912 = cop,12 ; User linking functions disable ; 913 = cop,13 ; Query system control state ; 914 = cop,14 ; Set system control state ; 915 = cop,15 ; Scheduler enable ; 916 = cop,16 ; Scheduler disable ; 917 = cop,17 ; User functions enable (time, id, etc) ; 918 = cop,18 ; User functions disable ; 919 = cop,19 ; Select alternate hang time (althangtime) ; 920 = cop,20 ; Select standard hangtime (hangtime) ; 924 = cop,24 ; Flush all telemetry ; 925 = cop,25 ; Query last node un-keyed ; 926 = cop,26 ; Query all nodes keyed/unkeyed ; 927 = cop,27 ; Reset DAQ minimum on a pin ; 928 = cop,28 ; Reset DAQ maximum on a pin ; 930 = cop,30 ; Recall Memory Setting in Attached Xcvr ; 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr ; 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed ; 933 = cop,33 ; Local Telemetry Output Enable ; 934 = cop,34 ; Local Telemetry Output Disable ; 935 = cop,35 ; Local Telemetry Output on Demand ; 936 = cop,36 ; Foreign Link Local Output Path Enable ; 937 = cop,37 ; Foreign Link Local Output Path Disable ; 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry ; 939 = cop,39 ; Foreign Link Local Output Path on Demand ; 942 = cop,42 ; Echolink announce node # only ; 943 = cop,43 ; Echolink announce node Callsign only ; 944 = cop,44 ; Echolink announce node # & Callsign ; 945 = cop,45 ; Link Activity timer enable ; 945 = cop,46 ; Link Activity timer disable ; 947 = cop,47 ; Reset "Link Config Changed" Flag ; 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis) ; 949 = cop,49 ; Disable incoming connections (control state noice) ; 950 = cop,50 ; Enable incoming connections (control state noicd) ; 951 = cop,51 ; Enable sleep mode ; 952 = cop,52 ; Disable sleep mode ; 953 = cop,53 ; Wake up from sleep ; 954 = cop,54 ; Go to sleep ; 956 = cop,56 ; Rx CTCSS Enable ; 957 = cop,57 ; Rx CTCSS Disable ; 958 = cop.58 ; Tx CTCSS On Input only Enable ; 959 = cop,59 ; Tx CTCSS On Input only Disable ; 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode]) ; ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call ; ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F. ; ; DestID and subcode are only specified for the 'C' type message. ; ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of ; ; the radio being called, and the subcodes are as follows: ; ; Subcode '8205' is Voice Selective Call for Spectra ('Call') ; ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or ; ; Astro-Saber('Call') ; ; Subcode '810D' is Call Alert (like Maxtrac 'CA') ; 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....) ; 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....) ; 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR]) ; 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR]) ; 965 = cop,65 ; Send POCSAG page (equipped channel types only) [functions-remote] 0 = remote,1 ; Retrieve Memory 1 = remote,2 ; Set freq. 2 = remote,3 ; Set tx PL tone 3 = remote,4 ; Set rx PL tone 40 = remote,100 ; Rx PL off 41 = remote,101 ; Rx PL on 42 = remote,102 ; Tx PL off 43 = remote,103 ; Tx PL on 44 = remote,104 ; Low Power 45 = remote,105 ; Medium Power 46 = remote,106 ; High Power 711 = remote,107 ; Bump -20 714 = remote,108 ; Bump -100 717 = remote,109 ; Bump -500 713 = remote,110 ; Bump +20 716 = remote,111 ; Bump +100 719 = remote,112 ; Bump +500 721 = remote,113 ; Scan - slow 724 = remote,114 ; Scan - quick 727 = remote,115 ; Scan - fast 723 = remote,116 ; Scan + slow 726 = remote,117 ; Scan + quick 729 = remote,118 ; Scan + fast 79 = remote,119 ; Tune 51 = remote,5 ; Long status query 52 = remote,140 ; Short status query 67 = remote,210 ; Send a * 69 = remote,211 ; Send a # ;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login. ; Define a different dtmf sequence for each user which is ; authorized to use the remote base to control access to it. ; For examble 9139583=remote,99,WB6NIL,G would grant access to ; the remote base and announce WB6NIL as being logged in. ; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to ; the remote base and announce WA6ZFT as being logged in. ; When the remote base is disconnected from the originating node, the ; user will be logged out. The LICENSETAG argument is used to enforce ; tx frequency limits. See [txlimits] below. 85 = cop,6 ; Remote base telephone key [telemetry] ; Telemetry entries can be shared across all repeaters, or defined for each repeater. ; Can be a tone sequence, morse string, or a file ; ; |t - Tone escape sequence ; ; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude) ; Single frequencies are created by setting freq1 or freq2 to zero. ; ; |m - Morse escape sequence ; ; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the ; [morse] section. ; ; Follow with an alphanumeric string ; ; |i - Morse ID escape sequence ; ; Sends Morse code at the ID amplitude and ID frequency as defined in the ; [morse] section. ; ; path/to/sound/file/without/extension ; ; Send the sound if in place of a constructed tone. Do not include the file extension ; Example: ct8 = rpt/bloop ; Example: idrecording = rpt/nodenames/48148 ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048) ct2 = |t(660,880,150,2048) ct3 = |t(440,0,150,4096) ct4 = |t(550,0,150,2048) ct5 = |t(660,0,150,2048) ct6 = |t(880,0,150,2048) ct7 = |t(660,440,150,2048) ct8 = |t(700,1100,150,2048) ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0) remotemon = |mR ;remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only remotetx = |mK ;remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode cmdmode = |t(900,903,200,2048) ;functcomplete = |mW functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048) remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048) pfxtone = |t(350,440,30000,3072) patchup = rpt/callproceeding patchdown = rpt/callterminated ct12 = |mI ct13 = |mR ; As far as what the numbers mean, ; (000,000,010,000) ; | | | |-------amplitude ; | | |-------------duration ; | |-------------------Tone 2 ; |-------------------------Tone 1 ; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude. ; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter) ; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048. ; Morse code parameters, these are common to all repeaters. [morse] speed = 18 ; Approximate speed in WPM frequency = 800 ; Morse Telemetry Frequency amplitude = 4096 ; Morse Telemetry Amplitude idfrequency = 1065 ; Morse ID Frequency idamplitude = 1024 ; Morse ID Amplitude ; ; This section allows wait times for telemetry events to be adjusted ; A section for wait times can be defined for every repeater ; [wait-times] telemwait = 400 ; Time to wait before sending most telemetry idwait = 500 ; Time to wait before starting ID unkeywait = 200 ; Time to wait after unkey before sending CT's and link telemetry calltermwait = 2000 ; Time to wait before announcing "call terminated" ; Memories for remote bases [memory] ;00 = 146.580,100.0,m ;01 = 147.030,103.5,m+t ;02 = 147.240,103.5,m+t ;03 = 147.765,79.7,m-t ;04 = 146.460,100.0,m ;05 = 146.550,100.0,m ; Place command macros here [macro] 11 = *141223# ; disc. hubnet 21 = *241223# ; monitor hubnet 31 = *341223# ; transceive hubnet 12 = *12197# ; disc Freestar 22 = *22197# ; monitor Freestar 32 = *32197# ; transceive Freestar 13 = *129332# ; disc Alaska 23 = *229332# ; monitor Alaska 33 = *329332# ; transceive Alaska 14 = *154383# ; disc CQ North 24 = *254383# ; monitor CQ North 34 = *354383# ; transceive CQ North 191 = *140894# ; disconnect hubnet Echo 391 = *340894# ; connect hubnet echo 192 = *13009999# ; dis echolink echotest 392 = *33009999# ; con echolink echotest ; Data Acquisition configuration ;[daq-list] ;device = device_name1 ;device = device_name2 ;Where: device_name1 and device_name2 are stanzas you define in this file ;device = daq-cham-1 ; Device name ;[daq-cham-1] ; Defined in [daq-list] ;hwtype = uchameleon ; DAQ hardware type ;devnode = /dev/ttyUSB0 ; DAQ device node (if required) ;1 = inadc ; Pin definition for an ADC channel ;2 = inadc ;3 = inadc ;4 = inadc ;5 = inadc ;6 = inadc ;7 = inadc ;8 = inadc ;9 = inp ; Pin definition for an input with a weak pullup resistor ;10 = inp ;11 = inp ;12 = inp ;13 = in ; Pin definition for an input without a weak pullup resistor ;14 = out ; Pin definition for an output ;15 = out ;16 = out ;17 = out ;18 = out ;[meter-faces] ;face = scale(scalepre,scalediv,scalepost),word/?,... ; ; scalepre = offset to add before dividing with scalediv ; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts). ; scalepost = offset to add after dividing with scalediv ; ;face = range(X-Y:word,X2-Y2:word,...),word/?,... ;face = bit(low-word,high-word),word/?,... ; ; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories, ; or a question mark which is a placeholder for the measured value. ; ; ; Battery voltage 0-20 volts ;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts ; 4 quadrant wind direction ;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,? ; LM34 temperature sensor with 130 deg. F full scale ;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit ; Status poll (non alarmed) ;light = bit(ha/off,ha/on),ha/light,? ;[alarms] ; ;tag = device,pin,node,ignorefirst,func-low,func-hi ; ;tag = a unique name for the alarm ;device = daq device to poll ;pin = the device pin to be monitored ;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it ;node = the node number to execute the function on ;func-low = the DTMF function to execute on a high to low transition ;func-high = the DTMF function to execute on a low to high transition ; ; a '-' as a function name is shorthand for no-operation ; ;door = daq-cham-1,9,1,2017,*7,- ;pwrfail = daq-cham-1,10,0,2017,*911111,- ; ; Control states ; Allow several control operator functions to be changed at once using one command (good for scheduling) ; ;[controlstates] ;statenum = copcmd,[copcmd]... ;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation ;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation ;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation ; Scheduler - execute a macro at a given time [schedule] ;dtmf_function = m h dom mon dow ; ala cron, star is implied ;8 = 55 12 * * * ; at midnight, execute macro 2. ; See https://wiki.allstarlink.org/wiki/Event_Management [events] #includeifexists custom/rpt.conf ++++ ==== simpleusb.conf ==== ++++ /etc/asterisk/simpleusb.conf | ; If you are going to use this channel driver, you MUST enable it in modules.conf ; change: ; noload => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP) ; to: ; load => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP) ; SimpleUSB configuration [general] [usb_48148] eeprom = 0 ; EEPROM installed: 0,1 ; 0 = no (default) ; 1 = yes hdwtype = 0 ; Leave this set to 0 for USB sound fobs modified using ; the instructions from usbfob.pdf. Use a setting of ; 1 is for Dingotel/Sph interfaces. ; Receiver parameters rxboost = 0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed ; Set to 1 for additonal gain if using a low-level receiver output carrierfrom = usb ; no,usb,usbinvert ; no - no carrier detection at all ; usb - from the COR line on the USB sound fob (Active high) ; usbinvert - from the inverted COR line on the USB sound fob (Active low) ctcssfrom = no ; no,usb,usbinvert ; no - CTCSS decoding, system will be carrier squelch ; usb - CTCSS decoding using input from USB sound fob (Active high) ; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low) deemphasis = yes ; enable de-emphasis (input from discriminator) plfilter = no ; enable PL filter ;rxondelay = 0 ; number of 20ms intervals to hold off receiver turn-on indication ; Transmitter parameters txmixa = voice ; Left channel output (A): no,voice ; no - Do not output anything ; voice - output voice only txmixb = no ; Right channel output (B): no,voice ; no - Do not output anything ; voice - output voice only txboost = 0 invertptt = 0 ; Invert PTT: 0,1 ; 0 - ground to transmit ; 1 - open to transmit preemphasis = yes ; Perform standard 6db/octave pre-emphasis ; pager = no ; no,a,b (e.g. pager = b means "put the normal repeat audio on channel A, and the pager audio on channel B") ; duplex3 = 0 ; duplex 3 gain setting (0 to disable) duplex = 0 ; Duplex 0,1 ; 0 - half duplex ; 1 - full duplex #includeifexists custom/simpleusb.conf ++++ ==== simpleusb_tune_usb_48148.conf ==== ++++ /etc/asterisk/simpleusb_tune_usb_48148.conf | [usb_48148] ; name=usb_48148 ; devicenum=1 devstr=1-1.2:1.0 rxmixerset=330 txmixaset=70 txmixbset=50 ++++ ==== crontab ==== ''00 * * * * sudo /usr/sbin/asterisk -rx "rpt localplay 481481 /home/gm4slv/mb7aze_id " >/dev/null 2>&1'' ''00 * * * * sleep 4 && sudo /usr/sbin/asterisk -rx "rpt fun 481481 *81" >/dev/null 2>&1'' * ID file (a uLaw audio file) for verbal announcements {{ :private:greenmeadow:mb7aze_id.zip |}} ===== allmon2 and supermon web files ===== ==== allmon2 ==== {{ :private:greenmeadow:allmon2.tar |}} ==== supermon ==== {{ :private:greenmeadow:supermon.tar |}} Page created Sun May 29 15:48:50 2022 by John Pumford-Green Page last updated: ~~LASTMOD~~ {{tag>pi radio allstar mb7aze}}