public:radio:dormant:allstar
Table of Contents
MB7AZE AllStar Config
all /etc/asterisk files
Main Config files
echolink.conf
[el0] call = MB7AZE-L ; Change this! pwd = xxxxxxxx ; Change this! name = John ; Change this! qth = allstar 481481 ; Change this! email = gm4slv@gm4slv.plus.com ; Change this! node = 879598 ; Change this! ; Data for EchoLink Status Page lat = 60.2883 ; Latitude in decimal degrees lon = -001.42533 ; Longitude in decimal degrees freq = 430.050 ; not mandatory Frequency in MHz tone = 0.0 ; not mandatory CTCSS Tone (0 for none) power = 1 ; 0=0W, 1=1W, 2=4W, 3=9W, 4=16W, 5=25W, 6=36W, 7=49W, 8=64W, 9=81W (Power in Watts) height = 0 ; 0=10 1=20 2=40 3=80 4=160 5=320 6=640 7=1280 8=2560 9=5120 (AMSL in Feet) gain = 0 ; Gain in db (0-9) dir = 0 ; 0=omni 1=45deg 2=90deg 3=135deg 4=180deg 5=225deg 6=270deg 7=315deg 8=360deg (Direction) maxstns = 5 ; Max Stations rtcptimeout = 10 recfile = /tmp/echolink_recorded.gsm ; astnode = 481481 ; Change this! context = radio-secure ; Default in code is echolink-in ; Max 3 servers server1 = nasouth.echolink.org server2 = naeast.echolink.org server3 = server3.echolink.org ; To deny w6xxx you would add the statement: deny = w6xxx ; To prohibit computer-based connections you would write: permit = *-* ; To allow access to only a select group of callsigns: permit = w6abc,w6def,... ; permit ; comma delimited list of callsign, type (-r) ; deny ; Remote text commands thru netcat: ; o.conip <IPaddress> (request a connect) ; o.dconip <IPaddress> (request a disconnect) ; o.rec (turn on/off recording) ; ipaddr ; port
manager.conf
; ; Asterisk Call Management support ; ; By default asterisk will listen on localhost only. [general] enabled = yes port = 5038 bindaddr = 127.0.0.1 [gm4slv] secret = llcgi read = all,system,call,log,verbose,command,agent,user,config write = all,system,call,log,verbose,command,agent,user,config
rpt.conf
; Radio Repeater configuration file (for use with app_rpt)
; Your Repeater
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;
; This is where you define your nodes which can be connected to.
;
[nodes]
; Note, if you are using automatic update for allstar link nodes,
; no allstar link nodes should be defined here. Only place a definition
; for your local nodes, and private (off of allstar link) nodes here.
;481480 = radio@127.0.0.1:4569/481480,NONE ; This must be changed to your node number
481481 = radio@127.0.0.1:4569/481481,NONE ; This must be changed to your node number
; and iax port number if not the default
;[481480] ; Change this to your assigned node number
[481481] ; Change this to your assigned node number
; Must also be enabled in modules.conf
; Rx audio/signalling channel. Choose ONLY 1 per node stanza
; Enable the selected channel driver in modules.conf !!!
;rxchannel = dahdi/pseudo ; No radio (hub)
rxchannel = SimpleUSB/usb_48148 ; SimpleUSB
; rxchannel = Pi/1 ; Raspberry Pi PiTA
; rxchannel = Radio/usb_48148 ; USBRadio (DSP)
; rxchannel = Dahdi/1 ; PCI Quad card
; rxchannel = Beagle/1 ; BeagleBoard
; rxchannel = USRP/127.0.0.1:34001:32001; GNU Radio interface USRP
; rxchannel = Voter/48148 ; RTCM device
duplex = 1 ; 0 = Half duplex with no telemetry tones or hang time.
; Special Case: Full duplex if linktolink is set to yes.
; This mode is preferred when interfacing with an external multiport repeater controller.
; Comment out idrecording and idtalkover to suppress IDs also
; 1 = Half duplex with telemetry tones and hang time. Does not repeat audio.
; This mode is preferred when interfacing a simplex node.
; 2 = Full Duplex with telemetry tones and hang time.
; This mode is preferred when interfacing a repeater.
; 3 = Full Duplex with telemetry tones and hang time, but no repeated audio.
; 4 = Full Duplex with telemetry tones and hang time. Repeated audio only when the autopatch is down.
linktolink = no ; disables forcing physical half-duplex operation of main repeater while
; still keeping half-duplex semantics (optional)
linkmongain = 0 ; Link Monitor Gain adjusts the audio level of monitored nodes when a signal from another node or the local receiver is received.
; If linkmongain is set to a negative number the monitored audio will decrease by the set amount in db.
; If linkmongain set to a positive number monitored audio will increase by the set amount in db.
; The value of linkmongain is in db. The default value is 0 db.
erxgain = -3 ; Echolink receive gain adjustment
; Note: Gain is in db-volts (20logVI/VO)
etxgain = 3 ; Echolink transmit gain adjustment
; Note: Gain is in db-volts (20logVI/VO)
eannmode = 2 ; 1 = Say only node number on echolink connects (default = 1)
; 2 = say phonetic call sign only on echolink connects
; 3 = say phonetic call sign and node number on echolink connects
;controlstates = controlstates ; system control state stanza
scheduler = schedule ; scheduler stanza
functions = functions ; Repeater Function stanza
phone_functions = functions ; Phone Function stanza
link_functions = functions ; Link Function stanza
telemetry = telemetry ; Telemetry stanza
morse = morse ; Morse stanza
wait_times = wait-times ; Wait times stanza
context = radio ; dialing context for phone
callerid = "Repeater" <0000000000> ; callerid for phone calls
accountcode = RADIO ; account code (optional)
hangtime = 200 ; squelch tail hang time (in ms) (optional, default 5 seconds, 5000 ms)
althangtime = 300 ; longer squelch tail
totime = 300000 ; 5 mins (12/4/22) transmit time-out time (in ms) (optional, default 3 minutes 180000 ms)
telemnomdb = -3 ;
telemduckdb = -10 ;
;idrecording = /home/gm4slv/gm4slv_id
;idrecording = /home/gm4slv/mb7aze_id
idrecording = |iDE MB7AZE ; Main ID message
;idtalkover = |iMB7AZE ; Talkover ID message
idtalkover = |iMB7AZE ; Talkover ID message
; See Telemetry section Example: idrecording = rpt/nodenames/48148
idtime = 900000 ; 15 mins (12/4/22) id interval time (in ms) (optional) Default 5 minutes (300000 ms)
politeid = 30000 ; time in milliseconds before ID timer expires to try and ID in the tail. (optional, default 30000)
unlinkedct = ct12 ; Send a this courtesy tone when the user unkeys if the node is not connected to any other nodes. (optional, default is none)
remotect = ct3 ; remote linked courtesy tone (indicates a remote is in the list of links)
linkunkeyct = ct4 ; sent when a transmission received over the link unkeys
;nolocallinkct = 0 ; Send unlinkedct instead if another local node is connected to this node (hosted on the same PC).
; Supermon smlogger
connpgm=/usr/local/sbin/supermon/smlogger 1
discpgm=/usr/local/sbin/supermon/smlogger 0
;connpgm = yourconnectprogram ; Disabled. Execute a program you specify on connect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being connected to us (them)
;discpgm = yourdisconnectprogram ; Disabled. Execute a program you specify on disconnect. (default)
; passes 2 command line arguments to your program:
; 1. node number in this stanza (us)
; 2. node number being disconnected from us (them)
lnkactenable = 0 ; Set to 1 to enable the link activity timer. Applicable to standard nodes only.
lnkacttime = 3600 ; Link activity timer time in seconds.
lnkactmacro = *73 ; Function to execute when link activity timer expires.
lnkacttimerwarn = custom/timeout ; Message to play when the link activity timer has 30 seconds left.
;remote_inact_timeout = 60 ; Specifies the amount of time without keying from the link. Set to 0 to disable timeout. (15 * 60)
;remote_timeout = ; Session time out for remote base. Set to 0 to disable. (60 * 60)
;remote_timeout_warning_freq = ; 30
;remote_timeout_warning = ; (3 * 60)
;nounkeyct = 0 ; Set to a 1 to eliminate courtesy tones and associated delays.
holdofftelem = 0 ; Hold off all telemetry when signal is present on receiver or from connected nodes
; except when an ID needs to be done and there is a signal coming from a connected node.
telemdefault = 1 ; 0 = telemetry output off
; 1 = telemetry output on (default = 1)
; 2 = timed telemetry output on command execution and for a short time thereafter.
telemdynamic = 1 ; 0 = disallow users to change the local telemetry setting with a COP command,
; 1 = Allow users to change the setting with a COP command. (default = 1)
beaconing = 1 ; Send ID regardless of repeater activity (Required in the UK, but probably illegal in the US)
parrotmode = 1 ; 0 = Parrot Off (default = 0)
; 1 = Parrot On Command
; 2 = Parrot Always
; 3 = Parrot Once by Command
parrottime = 1000 ; Set the amount of time in milliseconds
; to wait before parroting what was received
;rxnotch=1065,40 ; (Optional) Notch a particular frequency for a specified
; b/w. app_rpt must have been compiled with
; the notch option
startup_macro = *80*81*70
; nodenames = /var/lib/asterisk/sounds/rpt/nodenames.callsign ; Point to alternate nodename sound directory
; Stream your node audio to Broadcastify or similar. See https://wiki.allstarlink.org/wiki/Stream_Node_Audio_to_Broadcastify
; outstreamcmd = /bin/sh,-c,/usr/bin/lame --preset cbr 16 -r -m m -s 8 --bitwidth 16 - - | /usr/bin/ezstream -qvc /etc/ezstream.xml
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Need more information on these
;extnodes = extnodes-different ; section in extnodefile containing dynamic node information (optional)
;extnodefile = /home/gm4slv/rpt_extnodes ; Points to nodelist file containing dynamic node info default = /var/lib/asterisk/rpt_extnodes (optional)
;extnodefile2 = ; Is this a list of node files? Possible a list of private nodes or a list of static IPs for known nodes????
;nodenames = /foo/names ; locaton of node sound files default = /var/lib/asterisk/sounds/rpt/nodenames
;archivedir = /tmp ; defines and enables activity recording into specified directory (optional)
;monminblocks = 2048 ; Min 1K blocks to be left on partition (will not save monitor output if disk too full)
; ; The tailmessagetime,tailsquashedtime, and tailmessagelist need to be set
; ; to support tail messages. They can be omitted otherwise.
;tailmessagetime = 300000 ; Play a tail message every 5 mins
;tailsquashedtime = 30000 ; If squashed by another user,
; ; try again after 30 seconds
;tailmessagelist = msg1,msg2 ; list of messages to be played for tail message
; alt_functions
; ctgroup
; dphone_functions
; idtime
; iobase
; iospeed
; locallist
; mars Remote Base
; memory
; nobusyout
; nodes
; nolocallinkct
; notelemtx
; outxlat
; parrot
; propagate_phonedtmf
; rptnode
; rptinactmacro Macro to execute when inactivity timer expires
; rptinacttime Inactivity timer time in seconds (0 seconds disables feature)
; rxnotch Optional Audio notch
; simplexphonedelay
; tonemacro
; tonezone
; txlimits
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; *** Status Reporting ***
; Comment the following statpost line stop to reporting of the status of your node to stats.allstarlink.org
statpost_url = http://stats.allstarlink.org/uhandler ; Status updates
[functions]
; Prefix Functions
; *1 Disconnect Link
; *2 Monitor Link
; *3 Connect Link
; *4 Command Mode
; *5 Macros
; *6 User Functions
; *7 Connection Status/Functions
; *8 User Functions
; *9 User Functions
; *0 User Functions
; *A User Functions
; *B User Functions
; *C User Functions
; *D User Functions
; Mandatory Command Codes
1 = ilink,1 ; Disconnect specified link
2 = ilink,2 ; Connect specified link -- monitor only
3 = ilink,3 ; Connect specified link -- tranceive
4 = ilink,4 ; Enter command mode on specified link
70 = ilink,5 ; System status
;99 = cop,6 ; PTT (phone mode only)
; End Mandatory Command Codes
73 = ilink,6 ; Disconnect All Links
74 = ilink,16 ; Reconnect links disconnected with "disconnect all links"
80 = status,11 ; Force ID (local only)
81 = status,12 ; Give Time of Day (local only)
91 = cop,21 ; Enable Parrot Mode
92 = cop,22 ; Disable Parrot Mode
93 = cop,55 ; Parrot Once if parrot mode is disabled
98 = cop,2 ; System enable
99 = cop,3 ; System disable
901 = cop,1 ; System warm boot
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Macro Commands
5 = macro
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Autopatch Commands
; Note, This may be a good place for other 2 digit frequently used commands
;61 = autopatchup,noct = 1,farenddisconnect = 1,dialtime = 20000 ; Autopatch up
;62 = autopatchdn ; Autopatch down
; autopatchup can optionally take comma delimited setting=value pairs:
; context = string ; Override default context with "string"
; dialtime = ms ; Specify the max number of milliseconds between phone number digits (1000 milliseconds = 1 second)
; farenddisconnect = 1 ; Automatically disconnect when called party hangs up
; noct = 1 ; Don't send repeater courtesy tone during autopatch calls
; quiet = 1 ; Don't send dial tone, or connect messages. Do not send patch down message when called party hangs up
; Example: 123=autopatchup,dialtime=20000,noct=1,farenddisconnect=1
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Status Commands
; 1 - Force ID (global)
; 2 - Give Time of Day (global)
; 3 - Give software Version (global)
; 4 - Give GPS location info
; 5 - Last (dtmf) user
; 11 - Force ID (local only)
; 12 - Give Time of Day (local only)
;721 = status,1 ; Force ID (global)
;722 = status,2 ; Give Time of Day (global)
;723 = status,3 ; Give software Version (global)
;724 = status,4 ; Give GPS location info
;725 = status,5 ; Last (dtmf) user
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Link Commands
; 1 - Disconnect specified link
; 2 - Connect specified link -- monitor only
; 3 - Connect specified link -- tranceive
; 4 - Enter command mode on specified link
; 5 - System status
; 6 - Disconnect all links
; 7 - Last Node to Key Up
; 8 - Connect specified link -- local monitor only
; 9 - Send Text Message (9,<destnodeno or 0 (for all)>,Message Text, etc.
; 10 - Disconnect all RANGER links (except permalinks)
; 11 - Disconnect a previously permanently connected link
; 12 - Permanently connect specified link -- monitor only
; 13 - Permanently connect specified link -- tranceive
; 15 - Full system status (all nodes)
; 16 - Reconnect links disconnected with "disconnect all links"
; 17 - MDC test (for diag purposes)
; 18 - Permanently Connect specified link -- local monitor only
; ilink commands 1 through 5 are defined in the Mandatory Command section
;806 = ilink,6 ; Disconnect all links
;827 = ilink,7 ; Last Node to Key Up
;808 = ilink,8 ; Connect specified link -- local monitor only
;809 = ilink,9,48148,"Testing" ; would send a text message to node 48148 replace 48148 with 0 for all connected nodes
;810 = ilink,10 ; Disconnect all RANGER links (except permalinks)
;811 = ilink,11 ; Disconnect a previously permanently connected link
;812 = ilink,12 ; Permanently connect specified link -- monitor only
;823 = ilink,13 ; Permanently connect specified link -- tranceive
;815 = ilink,15 ; Full system status (all nodes)
;817 = ilink,17 ; MDC test (for diag purposes)
;818 = ilink,18 ; Permanently Connect specified link -- local monitor only
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Control operator (cop) functions.
; Change these to something other than these codes listed below!
; Uncomment as needed.
;901 = cop,1 ; System warm boot
; 904 = cop,4 ; Test tone on/off (toggle)
; 905 = cop,5 ; Dump system variables on console (debug use only)
; 907 = cop,7 ; Time out timer enable
; 908 = cop,8 ; Time out timer disable
; 909 = cop,9 ; Autopatch enable
; 910 = cop,10 ; Autopatch disable
; 911 = cop,11 ; User linking functions enable
; 912 = cop,12 ; User linking functions disable
; 913 = cop,13 ; Query system control state
; 914 = cop,14 ; Set system control state
; 915 = cop,15 ; Scheduler enable
; 916 = cop,16 ; Scheduler disable
; 917 = cop,17 ; User functions enable (time, id, etc)
; 918 = cop,18 ; User functions disable
; 919 = cop,19 ; Select alternate hang time (althangtime)
; 920 = cop,20 ; Select standard hangtime (hangtime)
; 924 = cop,24 ; Flush all telemetry
; 925 = cop,25 ; Query last node un-keyed
; 926 = cop,26 ; Query all nodes keyed/unkeyed
; 927 = cop,27 ; Reset DAQ minimum on a pin
; 928 = cop,28 ; Reset DAQ maximum on a pin
; 930 = cop,30 ; Recall Memory Setting in Attached Xcvr
; 931 = cop,31 ; Channel Selector for Parallel Programmed Xcvr
; 932 = cop,32 ; Touchtone pad test: command + Digit string + # to playback all digits pressed
; 933 = cop,33 ; Local Telemetry Output Enable
; 934 = cop,34 ; Local Telemetry Output Disable
; 935 = cop,35 ; Local Telemetry Output on Demand
; 936 = cop,36 ; Foreign Link Local Output Path Enable
; 937 = cop,37 ; Foreign Link Local Output Path Disable
; 938 = cop,38 ; Foreign Link Local Output Path Follows Local Telemetry
; 939 = cop,39 ; Foreign Link Local Output Path on Demand
; 942 = cop,42 ; Echolink announce node # only
; 943 = cop,43 ; Echolink announce node Callsign only
; 944 = cop,44 ; Echolink announce node # & Callsign
; 945 = cop,45 ; Link Activity timer enable
; 945 = cop,46 ; Link Activity timer disable
; 947 = cop,47 ; Reset "Link Config Changed" Flag
; 948 = cop,48 ; Send Page Tone (Tone specs separated by parenthesis)
; 949 = cop,49 ; Disable incoming connections (control state noice)
; 950 = cop,50 ; Enable incoming connections (control state noicd)
; 951 = cop,51 ; Enable sleep mode
; 952 = cop,52 ; Disable sleep mode
; 953 = cop,53 ; Wake up from sleep
; 954 = cop,54 ; Go to sleep
; 956 = cop,56 ; Rx CTCSS Enable
; 957 = cop,57 ; Rx CTCSS Disable
; 958 = cop.58 ; Tx CTCSS On Input only Enable
; 959 = cop,59 ; Tx CTCSS On Input only Disable
; 960 = cop,60 ; Send MDC-1200 Burst (cop,60,type,UnitID[,DestID,SubCode])
; ; Type is 'I' for PttID, 'E' for Emergency, and 'C' for Call
; ; (SelCall or Alert), or 'SX' for STS (ststus), where X is 0-F.
; ; DestID and subcode are only specified for the 'C' type message.
; ; UnitID is the local systems UnitID. DestID is the MDC1200 ID of
; ; the radio being called, and the subcodes are as follows:
; ; Subcode '8205' is Voice Selective Call for Spectra ('Call')
; ; Subcode '8015' is Voice Selective Call for Maxtrac ('SC') or
; ; Astro-Saber('Call')
; ; Subcode '810D' is Call Alert (like Maxtrac 'CA')
; 961 = cop,61 ; Send Message to USB to control GPIO pins (cop,61,GPIO1=0[,GPIO4=1].....)
; 962 = cop,62 ; Send Message to USB to control GPIO pins, quietly (cop,62,GPIO1=0[,GPIO4=1].....)
; 963 = cop,63 ; Send pre-configred APRSTT notification (cop,63,CALL[,OVERLAYCHR])
; 964 = cop,64 ; Send pre-configred APRSTT notification, quietly (cop,64,CALL[,OVERLAYCHR])
; 965 = cop,65 ; Send POCSAG page (equipped channel types only)
[functions-remote]
0 = remote,1 ; Retrieve Memory
1 = remote,2 ; Set freq.
2 = remote,3 ; Set tx PL tone
3 = remote,4 ; Set rx PL tone
40 = remote,100 ; Rx PL off
41 = remote,101 ; Rx PL on
42 = remote,102 ; Tx PL off
43 = remote,103 ; Tx PL on
44 = remote,104 ; Low Power
45 = remote,105 ; Medium Power
46 = remote,106 ; High Power
711 = remote,107 ; Bump -20
714 = remote,108 ; Bump -100
717 = remote,109 ; Bump -500
713 = remote,110 ; Bump +20
716 = remote,111 ; Bump +100
719 = remote,112 ; Bump +500
721 = remote,113 ; Scan - slow
724 = remote,114 ; Scan - quick
727 = remote,115 ; Scan - fast
723 = remote,116 ; Scan + slow
726 = remote,117 ; Scan + quick
729 = remote,118 ; Scan + fast
79 = remote,119 ; Tune
51 = remote,5 ; Long status query
52 = remote,140 ; Short status query
67 = remote,210 ; Send a *
69 = remote,211 ; Send a #
;91 = remote,99,CALLSIGN,LICENSETAG ; Remote base login.
; Define a different dtmf sequence for each user which is
; authorized to use the remote base to control access to it.
; For examble 9139583=remote,99,WB6NIL,G would grant access to
; the remote base and announce WB6NIL as being logged in.
; Another entry, 9148351=remote,99,WA6ZFT,E would grant access to
; the remote base and announce WA6ZFT as being logged in.
; When the remote base is disconnected from the originating node, the
; user will be logged out. The LICENSETAG argument is used to enforce
; tx frequency limits. See [txlimits] below.
85 = cop,6 ; Remote base telephone key
[telemetry]
; Telemetry entries can be shared across all repeaters, or defined for each repeater.
; Can be a tone sequence, morse string, or a file
;
; |t - Tone escape sequence
;
; Tone sequences consist of 1 or more 4-tuple entries (freq1, freq2, duration, amplitude)
; Single frequencies are created by setting freq1 or freq2 to zero.
;
; |m - Morse escape sequence
;
; Sends Morse code at the telemetry amplitude and telemetry frequency as defined in the
; [morse] section.
;
; Follow with an alphanumeric string
;
; |i - Morse ID escape sequence
;
; Sends Morse code at the ID amplitude and ID frequency as defined in the
; [morse] section.
;
; path/to/sound/file/without/extension
;
; Send the sound if in place of a constructed tone. Do not include the file extension
; Example: ct8 = rpt/bloop
; Example: idrecording = rpt/nodenames/48148
ct1 = |t(350,0,100,2048)(500,0,100,2048)(660,0,100,2048)
ct2 = |t(660,880,150,2048)
ct3 = |t(440,0,150,4096)
ct4 = |t(550,0,150,2048)
ct5 = |t(660,0,150,2048)
ct6 = |t(880,0,150,2048)
ct7 = |t(660,440,150,2048)
ct8 = |t(700,1100,150,2048)
ranger = |t(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,50,0)(1800,0,60,3072)(0,0,150,0)
remotemon = |mR
;remotemon = |t(1209,0,50,2048) ; local courtesy tone when receive only
remotetx = |mK
;remotetx = |t(1633,0,50,3000)(0,0,80,0)(1209,0,50,3000) ; local courtesy tone when linked Trancieve mode
cmdmode = |t(900,903,200,2048)
;functcomplete = |mW
functcomplete = |t(1000,0,100,2048)(0,0,100,0)(1000,0,100,2048)
remcomplete = |t(650,0,100,2048)(0,0,100,0)(650,0,100,2048)(0,0,100,0)(650,0,100,2048)
pfxtone = |t(350,440,30000,3072)
patchup = rpt/callproceeding
patchdown = rpt/callterminated
ct12 = |mI
ct13 = |mR
; As far as what the numbers mean,
; (000,000,010,000)
; | | | |-------amplitude
; | | |-------------duration
; | |-------------------Tone 2
; |-------------------------Tone 1
; So, with 0,0,10,0 That says No Tone1, No Tone2, 10ms duration, 0 Amplitude.
; Use it for a delay. Fine tuning for how long before telemetry is sent, in conjunction with the telemdelay parameter)
; The numbers, like 350,440,10,2048 are 350Hz, 440Hz, 10ms delay, amplitude of 2048.
; Morse code parameters, these are common to all repeaters.
[morse]
speed = 18 ; Approximate speed in WPM
frequency = 800 ; Morse Telemetry Frequency
amplitude = 4096 ; Morse Telemetry Amplitude
idfrequency = 1065 ; Morse ID Frequency
idamplitude = 1024 ; Morse ID Amplitude
;
; This section allows wait times for telemetry events to be adjusted
; A section for wait times can be defined for every repeater
;
[wait-times]
telemwait = 400 ; Time to wait before sending most telemetry
idwait = 500 ; Time to wait before starting ID
unkeywait = 200 ; Time to wait after unkey before sending CT's and link telemetry
calltermwait = 2000 ; Time to wait before announcing "call terminated"
; Memories for remote bases
[memory]
;00 = 146.580,100.0,m
;01 = 147.030,103.5,m+t
;02 = 147.240,103.5,m+t
;03 = 147.765,79.7,m-t
;04 = 146.460,100.0,m
;05 = 146.550,100.0,m
; Place command macros here
[macro]
11 = *141223# ; disc. hubnet
21 = *241223# ; monitor hubnet
31 = *341223# ; transceive hubnet
12 = *12197# ; disc Freestar
22 = *22197# ; monitor Freestar
32 = *32197# ; transceive Freestar
13 = *129332# ; disc Alaska
23 = *229332# ; monitor Alaska
33 = *329332# ; transceive Alaska
14 = *154383# ; disc CQ North
24 = *254383# ; monitor CQ North
34 = *354383# ; transceive CQ North
191 = *140894# ; disconnect hubnet Echo
391 = *340894# ; connect hubnet echo
192 = *13009999# ; dis echolink echotest
392 = *33009999# ; con echolink echotest
; Data Acquisition configuration
;[daq-list]
;device = device_name1
;device = device_name2
;Where: device_name1 and device_name2 are stanzas you define in this file
;device = daq-cham-1
; Device name
;[daq-cham-1] ; Defined in [daq-list]
;hwtype = uchameleon ; DAQ hardware type
;devnode = /dev/ttyUSB0 ; DAQ device node (if required)
;1 = inadc ; Pin definition for an ADC channel
;2 = inadc
;3 = inadc
;4 = inadc
;5 = inadc
;6 = inadc
;7 = inadc
;8 = inadc
;9 = inp ; Pin definition for an input with a weak pullup resistor
;10 = inp
;11 = inp
;12 = inp
;13 = in ; Pin definition for an input without a weak pullup resistor
;14 = out ; Pin definition for an output
;15 = out
;16 = out
;17 = out
;18 = out
;[meter-faces]
;face = scale(scalepre,scalediv,scalepost),word/?,...
;
; scalepre = offset to add before dividing with scalediv
; scalediv = full scale/number of whole units (e.g. 256/20 or 12.8 for 20 volts).
; scalepost = offset to add after dividing with scalediv
;
;face = range(X-Y:word,X2-Y2:word,...),word/?,...
;face = bit(low-word,high-word),word/?,...
;
; word/? is either a word in /var/lib/asterisk/sounds or one of its subdirectories,
; or a question mark which is a placeholder for the measured value.
;
;
; Battery voltage 0-20 volts
;batvolts = scale(0,12.8,0),rpt/thevoltageis,?,ha/volts
; 4 quadrant wind direction
;winddir = range(0-33:north,34-96:west,97-160:south,161-224:east,225-255:north),rpt/thewindis,?
; LM34 temperature sensor with 130 deg. F full scale
;lm34f = scale(0,1.969,0),rpt/thetemperatureis,?,degrees,fahrenheit
; Status poll (non alarmed)
;light = bit(ha/off,ha/on),ha/light,?
;[alarms]
;
;tag = device,pin,node,ignorefirst,func-low,func-hi
;
;tag = a unique name for the alarm
;device = daq device to poll
;pin = the device pin to be monitored
;ignorefirstalarm = set to 1 to throwaway first alarm event, or 0 to report it
;node = the node number to execute the function on
;func-low = the DTMF function to execute on a high to low transition
;func-high = the DTMF function to execute on a low to high transition
;
; a '-' as a function name is shorthand for no-operation
;
;door = daq-cham-1,9,1,2017,*7,-
;pwrfail = daq-cham-1,10,0,2017,*911111,-
;
; Control states
; Allow several control operator functions to be changed at once using one command (good for scheduling)
;
;[controlstates]
;statenum = copcmd,[copcmd]...
;0 = rptena,lnkena,apena,totena,ufena,noicd ; Normal operation
;1 = rptena,lnkena,apdis,totdis,ufena,noice ; Net and news operation
;2 = rptena,lnkdis,apdis,totena,ufdis,noice ; Repeater only operation
; Scheduler - execute a macro at a given time
[schedule]
;dtmf_function = m h dom mon dow ; ala cron, star is implied
;8 = 55 12 * * * ; at midnight, execute macro 2.
; See https://wiki.allstarlink.org/wiki/Event_Management
[events]
#includeifexists custom/rpt.conf
simpleusb.conf
; If you are going to use this channel driver, you MUST enable it in modules.conf
; change:
; noload => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
; to:
; load => chan_simpleusb.so ; CM1xx USB Cards with Radio Interface Channel Driver (No DSP)
; SimpleUSB configuration
[general]
[usb_48148]
eeprom = 0 ; EEPROM installed: 0,1
; 0 = no (default)
; 1 = yes
hdwtype = 0 ; Leave this set to 0 for USB sound fobs modified using
; the instructions from usbfob.pdf. Use a setting of
; 1 is for Dingotel/Sph interfaces.
; Receiver parameters
rxboost = 0 ; 0 = 20db attenuator inserted, 1= 20db attenuator removed
; Set to 1 for additonal gain if using a low-level receiver output
carrierfrom = usb ; no,usb,usbinvert
; no - no carrier detection at all
; usb - from the COR line on the USB sound fob (Active high)
; usbinvert - from the inverted COR line on the USB sound fob (Active low)
ctcssfrom = no ; no,usb,usbinvert
; no - CTCSS decoding, system will be carrier squelch
; usb - CTCSS decoding using input from USB sound fob (Active high)
; usbinvert - from the inverted CTCSS line on the USB sound fob (Active low)
deemphasis = yes ; enable de-emphasis (input from discriminator)
plfilter = no ; enable PL filter
;rxondelay = 0 ; number of 20ms intervals to hold off receiver turn-on indication
; Transmitter parameters
txmixa = voice ; Left channel output (A): no,voice
; no - Do not output anything
; voice - output voice only
txmixb = no ; Right channel output (B): no,voice
; no - Do not output anything
; voice - output voice only
txboost = 0
invertptt = 0 ; Invert PTT: 0,1
; 0 - ground to transmit
; 1 - open to transmit
preemphasis = yes ; Perform standard 6db/octave pre-emphasis
; pager = no ; no,a,b (e.g. pager = b means "put the normal repeat audio on channel A, and the pager audio on channel B")
; duplex3 = 0 ; duplex 3 gain setting (0 to disable)
duplex = 0 ; Duplex 0,1
; 0 - half duplex
; 1 - full duplex
#includeifexists custom/simpleusb.conf
simpleusb_tune_usb_48148.conf
/etc/asterisk/simpleusb_tune_usb_48148.conf
[usb_48148] ; name=usb_48148 ; devicenum=1 devstr=1-1.2:1.0 rxmixerset=330 txmixaset=70 txmixbset=50
crontab
00 * * * * sudo /usr/sbin/asterisk -rx “rpt localplay 481481 /home/gm4slv/mb7aze_id ” >/dev/null 2>&1
00 * * * * sleep 4 && sudo /usr/sbin/asterisk -rx “rpt fun 481481 *81” >/dev/null 2>&1
- ID file (a uLaw audio file) for verbal announcements mb7aze_id.zip
allmon2 and supermon web files
allmon2
supermon
Page created Sun May 29 15:48:50 2022 by John Pumford-Green
Page last updated: 06/03/25 06:49 GMT
public/radio/dormant/allstar.txt · Last modified: 06/03/25 06:49 GMT by 127.0.0.1